25337872893 Kenmore Refrigerator - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Henry D from PETERSTOWN, WV
- Parts Used:
- 215846602
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Screw drivers
sometimes it would go into defrost and would not go back to cooling.
I called the repairman who diagnosed the problem as a thermostat then had to order a thermostat took about 2 weeks to get back and install (cost little over $100). did good for about two weeks and same problem reoccured. I decided it was defrost timer and ordered from this site for $19.95 including shipping. I got on ( you tube ) and got instructions(recommend you tube) for DIY install about 15 to 20 minutes. Has been running great for about 3 weeks. ( YOU TUBE IS GREAT FOR A DIY REPAIR ON ABOUT ANYTHING)
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Alan from SAN MATEO, CA
- Parts Used:
- 316538904
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Repaired Oven Range Light Bulb
The bulb has a plastic clear cover. That cover can just be carefully removed using a screwdriver. It's held in by a metal bracket. After you remove the cover. You'll just need to replace the bulb and then re-install the cover and bracket.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- JOYCE from CHICAGO, AL
- Parts Used:
- 5303207345
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Gasket was worn
Removed all the screws. Replaced the gasket put all the screws back. This would work great if the door wasn't out of alignment.
Now I have a new refridgerator coming on Monday.
Now I have a new refridgerator coming on Monday.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Terry from KEYSTONE, IN
- Parts Used:
- 5303918277
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver
Ice maker leaking, then would'nt shut off.
Ice maker is held by 2 screws just above the unit, on the wall of the refrigerator. You can't see the screws, so borrow your wife's makeup mirror. Shine a light into the refrigerator, and using the mirror, locate the two screws, holding the unit in place, on the wall of the refrigerator. Using a nut driver, or socket wrench, with a 1/4 in socket, loosen up the two screws, but don't remove them. Bump the unit upwards, and away from the screws. (BEFORE doing anything!! Shut off the water supply, unplug the refrigerator) When you get the unit freed up, just unplug the old unit, and install the new one. You don't even have to worry about the water lines, and you'll see why, when you get the old unit off. Just reverse the procedure, installing the new unit. Very Simple, 10 to 15 minutes tops.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Curt from Maple Grove, MN
- Parts Used:
- 215846602
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver
Freezer too cold
Removed the housing with the light, 4 hexhead screws. This exposed the defrost timer, removed 2 hexhead screws, electrical connector and reassembled the unit.
Great resource and service, thank you.
Great resource and service, thank you.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Tunis from NOLANVILLE, TX
- Parts Used:
- 297216600
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Freezer wouldn't shut off and wouldn't reach cold enough temperature.
Removed existing part, tested it, found it to be defective. OrderEd a new one and replaced the existing one.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Danny from PUEBLO, CO
- Parts Used:
- 241798231
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver
Drive great stripped for ice eject. Heater bad
Loosened the 2 bolts 4 turns where it mounts inside the freezer. Lift maker off the bolts unplug 1 plug. Reverse to install.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Les from Fenton, MO
- Parts Used:
- 215846602
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver
Freezer icing up and refrigerator section not cold
Removed four screws for cover on refrigerator temperature controls, unpluged old timer and pluged in new timer. Replaced cover and screws.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- James from KNOXVILLE, TN
- Parts Used:
- 241798231
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Ice maker would dump ice one time and then stop. Turning the ice maker off for a minute and back on would repeat the process.
I removed the two side mount screws with a screwdriver and disconnected the electrical plug to the ice maker to remove it. I reversed the process to install the new one.
It was the thermostat that was the problem, but I chose to replace the entire ice maker for only $25 more.
It was the thermostat that was the problem, but I chose to replace the entire ice maker for only $25 more.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Thomas from WESTAMPTON, NJ
- Parts Used:
- 241798231
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver
Ice maker stopped making ice.
The repair was fast and easy .I removed the ice tray , disconnected the wiring connector and lossend two screws. I removed ice maker assy.and repeated in reverse order to install. I also installed a new water filter. I had ice in about 20 minutes.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- James from VOLANT, PA
- Parts Used:
- 215846602
- Difficulty Level:
- Easy
- Total Repair Time:
- 1- 2 hours
- Tools:
- Nutdriver, Screw drivers
defrost heater not working; defrost timer not rotating so coils ice up
Checked for continuity in heater, defrost thermostat and defrost timer. Heater good; not sure about thermostat or timer. Replaced thermostat - no change. Replaced timer - rotating and heater working.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Garry from Wetumpka, AL
- Parts Used:
- 5304414782
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver
No Ice
Replaced the Ice Maker unit. Produced fair amount of ice for several days then stopped. Replaced water inlet valve. Made ice a few times only. No ice at all now. Frozen water is in the ice tray but that's it. No ice. I'll have to remove/ inspect the ice maker again and check the water supply line and valve to see what is preventing ice maker to produce. Replacement ice maker seems to be dead. Thanks, G.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Mark from Partlow, VA
- Parts Used:
- 5300158289
- Difficulty Level:
- Very Difficult
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Socket set
Motor squeal
I didn’t do the repair because the new motor had a female pigtail connector while the original motor has male connection. It came with wire clamps but didn’t want to cut wires to make repair. The pictures online show a male connection. Put the old motor back in and now it works fine.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- John from San Diego, CA
- Parts Used:
- 215846602
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
The refrigerator wasn't cold enough.
I removed the plastic shroud on the ceiling of the refigerator, unscrewed and unplugged the old defrost timer, and replaced it with the new one. I reinstalled the shroud with the new timer installed.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Edward from GROTON, CT
- Parts Used:
- 241798231
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver
Ice maker stopped working. Part needed to repair it no longer available so had to replace the whole icemaker.
Loosened the two mounting screws (no need to remove them), lift off the icemaker and unplug it. Reverse the order and done.
Was this instruction helpful to you?
Thank you for voting!