25362073301 Kenmore Refrigerator - Instructions

1. I took out one screw on the ice maker and loosened the other two screws and unplugged and removed the ice maker.
2. Next I took out 2 screws from the bottom of the auger drive box and unplugged the wiring harness and removed the box. The wiring harness was a little tricky. The lock on the plug pushes in to unlock even though it looks like it pulls out,.
3.next you must remove 2 screws from the left side bracket that holds the auger box and remove the bracket.
4.Now take out 8 screws that hold the back panel in place and remove the back panel.
5. now your looking at the evaporator fan blade and motor. The simple way to replace the fan blade is to unplug the motor and remove it from the freezer. It just sits in with nothing holding it. The fan requires a little pressure but should pull right off. Install new fan blade and put everything back in the same order it was removed.

Looked up similar problems and found it to be the defrost timer. All I had to do was remove the plastic portion in the fridge section to get to the old timer. Popped the new one in and put it back together. Works great now. Would have been almost $150 to have a repair company come out and fix it.

Used hair dryer to warm up the gasket and it installed easily. Shelf just slid right in.

The center door hinge was still attached to the refridgerator so I only had to install the bottom and top hinges. I also moved the door handles to the other side so the doors open the "right" way. The hinges were just 2 bolts and 3 screws. Now, just if the repair man from our home warrentee company would show up to fix the refridgerator. It's blowing hot air!!!

Popped the old one out and pressed the new one in. Very easy. Pressed new one in my hands. Fits in a channel. Very easy

Remove screws from lower hinge and carefully remove the door. In my case it was the lower bearing, flip door upside down being careful to remove anything which might fall off first. I removed the door stop and then pulled the broken bearing out with pliers. Then I pushed the new one in and reassembled it.

Unplug, remove 2 screws off back panel inside the freezer. Cut wires on old one and crimped in new one. Light to melt the shrink wrap that came with it. Pretty easy.

Removed the housing with the light, 4 hexhead screws. This exposed the defrost timer, removed 2 hexhead screws, electrical connector and reassembled the unit.

Great resource and service, thank you.

First I removed the plastic grill (pulled out, no screws) from bottom of refrigerator, then I removed electrical plug & two screws from old timer (timer located on the front inside left lower side of refrigerator). Installed in reverse order.

The repair was not difficult because you just remove the old part and plug it in and connect two wires. But I wish there was a way to test if the compressor is working before I purchased the parts. The compressor would not start so I was not able to repair the refrigerator.

Removed the screws on the piece holding the switch which is at the front of the ceiling of the refrigerator box. Removed the old switch and replaced it. Very simple repair.

I removed the housing at the top of the refrigerator compartment that contained the reefer light and temperature adjustment knob. This required a small nut-driver. Inside, I found the old defrost control, unplugged it, unscrewed it with a Phillips screwdriver, and replaced it with the replacement part. Then I replaced the housing to its original position.

Removed four screws for cover on refrigerator temperature controls, unpluged old timer and pluged in new timer. Replaced cover and screws.

The bulb has a plastic clear cover. That cover can just be carefully removed using a screwdriver. It's held in by a metal bracket. After you remove the cover. You'll just need to replace the bulb and then re-install the cover and bracket.

I called the repairman who diagnosed the problem as a thermostat then had to order a thermostat took about 2 weeks to get back and install (cost little over $100). did good for about two weeks and same problem reoccured. I decided it was defrost timer and ordered from this site for $19.95 including shipping. I got on ( you tube ) and got instructions(recommend you tube) for DIY install about 15 to 20 minutes. Has been running great for about 3 weeks. ( YOU TUBE IS GREAT FOR A DIY REPAIR ON ABOUT ANYTHING)