3639502780 Kenmore Refrigerator - Instructions

Got the part in and needed two screws to installed on left side. Service was great on the part as it was delivered in 3 days from the time we ordered. Thanks for the quick service

First removed the old sliders, then screwed in the new sliders, replaced all four within minutes.

First removed the two screws that holds the old ice maker in place. Unplugged it. The freezer compartment was too narrow to allow the unit to slide out or turn in any other direction. Had to also remove the two front screws from the left side ice bin track and swing it down. The door opening was also too tight. Scratched the plastic door jamb putting the new unit in but other than that all is well and functioning well.

Installation could not have been easier!

replaced lights in refrigirator and freezer

Pulled out the shelves, unscrewed the old rail and removed it. Two screws put the new rail on, and then I put the shelves back in. It was so simple, and inexpensive too. This is a great service you provide. Thanks!!

I looked up the brand (Kenmore) and found that there are replacement parts for the drawer rails. I put up with this problem for three years not knowing this could be repaired. I unscrewed the broken left rail and replaced with the new one. I bought a right side rail just in case all the stress of the other side being broken would cause the right side to give up too. So far so good but I will keep the new right rail for a future date. It was so easy to repair and I wasted all those years putting up with the hassel.

unscrewed 2 screws per rail, replaced with new rails with 2 screws each - couldn't have been easier

I loosened the compression nut on the valve with my fingers and pulled the water line free from the valve. On the other end, I just pulled it from the hose clamp. Installation in reverse. Force the water line into the fitting on top, Slide the old nut over the line on the bottom. Screw the nut onto the valve. Reach inside the freezer and turn on the ice maker. Done. Before replacing the cardboard grill, you should vacuum the coils on the bottom, front and back. If practical, push it outside and blow it out with an air compressor or a leaf blower.

First I removed the electrical plug from the back of the freezer that plugs into the icemaker. I then removed the two hex head screws that hold the icemaker to the wall of the freezer and removed the icemaker. I removed the plastic cover, which incidentally protects the gears, by prying it off with a srewdriver. I removed three small nuts(7mm) which holds the internal cam in place. I removed the cam by pulling it off the shaft. Once I got the part from you folks I reversed the procedure that I just mentioned, and put the icemaker back together. It works great. The part with shipping was around $16.00. A new icemaker was roughly $159.00. If I would have called a technician it would have cost around $300.00 to repair.

Ordered at PartSelect and received the auger and blade within days. Printed the parts diagram and proceeded to take the auger apart the time it took would have been much less but I seized the opportunity to do a deep cleaning of the old parts before replacing them....The part diagram was the key to simplicity and the fast shipping was awesome. Thanks I'll be back....

First I removed the top hinge of the refrigerator door and then lifted it off the bottom assembly. I had to turn the door on its side to work on the bottom where the broken part was located. I unscrewed the bottom assembly and replaced the broken part with the new door cam. Put it all back together and now the door closes but must be manually pushed to close. When the door was working properly it would shut automatically when released from any position. I think I need to install an additional part - maybe a shim? to make it close automatically. That will be another story.
This was a fairly simple jog to do but since I did not have the proper tools it did take me longer than usual to remove the bolts. I'm happy I did it myself and saved a big repair bill! Thanks to the people at PartSelect.com.

remove the 8 screws 2 for each rail
installed the new rails
slid in the meat drawer and glass
slid in the vegetable drawer and glass
presto - like new fridge !

I had made a dry run at the repair after watching the instructional film provided by part select and it seemed easy enough.
The only problem was that i needed to use the electrical cord extender (provided) to adapt to my plug type. That presented a problm because it needed to be tucked up out of the way to allow the ice bin to clear. Just needed to be creative in how you wrapped the cord behind the ice maker unit before snugging the attachment screws.
Cranking out ice like crazy.

Removed the screws holding old rails on, replaced with new rails - using opposite side to gain an understanding of the small plastic pieces and how they were to be placed. there were on directions with the parts. The age of the refridgerator contributed to the need to thourally wash the area's behind the rails - what a pain to get gunk off. the area is small and is somewhat tight to get into. the Parts came remarkably quick and that was a great surprise- thanks