25331622107 Kenmore Refrigerator - Instructions

Removed two screws to get to defrost time pull panel down remove two screws holding time and reinstall

All 3 parts were very easy to replace. Thawing out the freezer took the most time. Great videos that go with each part for installation. I will be purchasing again from this company when needed.

took 4 screws out of the discharge vent on top of the refrigerator section and unpluged the wiring harness and put the section on the counter and unscrewed the timer and put the new one in and reinstalled the assembly and plugged the Jack and put the 4 screws back in, and rotated the timer and put it on defrost removed the back and check the heaters and drain .

just like the video showed...it was excellent!!!

Had my 3 year old remove the 4 screws to holds the carboard in place. Pryde the old fan blade off with a screwdriver. slid the new fan blade on to the shaft then my 3 year old put the screws back in.

first I replaced the timer control hoping thats the problem,unfortunately situation the same ice build up on the freezer.so I replaced the defrost thermostat.right now I'll still observing the condition if still the same.may be in couple days.so far its good.and to replace the parts is not difficult and easy.

When my side by side Kenmore refrigerator quit keeping the top half of my freezer and refrigerator cold I called Sears to see how much it would cost to get it checked out and fixed. Bottom line it was going to cost minimum $65 (which was just for him to come out) to $250 on up depending on what the problem was. So i decided to "do it myself"! I took it apart and within a few minutes figured out that it was my evaporator fan. So I went to sears to order the part based on the part number and with shipping and handling it was going to cost $125. While at sears I got on one of their computers and quickly looked up Kenmore parts and partselect.com came up and I quickly found the part for $62 and I chose overnight delivery and spent a total of like $83. When my part arrived I realized that the wiring/plug ins didn't quite match up. So I got online and went to their website and found a video for "do it yourself'ers" like me on how to splice the wiring to make it match. It took me about 20 min to splice the wire and put my refrigerator back together and IT WORKED! Easy easy easy and I saved moocho bucks! Ill never pay a repairman again. Oh and by the way, I am blond! :-)

Followed instruction vedeo from partselect. THANKS!!!!!

I removed the back panel ,cardboard-three screws,pushed the old fan blade off the motor and pushed the new fan on.Extremely easy.

unplugged frig,removed bottom front cover and loosend 2 screws at bottom front left and slid defrost timer out from behind metal panel,unplugged the old and plugged in the new.frig works great.

pulled down the thermostat cover and unpluged the timer control and replaced it with the new part. total time to repair was about 15 min. there was a vidio on how to replace the new part that just informed me that I did it right!!!!very easy site to find what you are looking for!!!!

replaced the defrosting timer and saved a lot of $ by doing it my self.

Unplugged the frig. Removed temp control module from frig, 1 screw with nut driver. Activated defrost timer by rotating adjustment until 2 clicks are heard. Removed two timer mounting screws, unpluged timer, plugged in the new timer, mounted it to the control module with 2 mounting screws. Replaced control module with the 1 mounting screw. Closed door and plugged it up.

This repair on this model is super easy because the shroud for the fan is not really attached except for the bottom so I was able to gently bend it to give em enough space to pull the broken fan off and put the new one on.

I followed the procedure online and found the thermostat was ok, it had continuity when cold, and the heater coil was also ok, it too had continuity, therefore the problem was a bad defrost timer. the refrigerator works great, thanks parts select!