1069658410 Kenmore Refrigerator - Instructions

We went online, found the part, and had it delivered to our rental house in Nags Head, NC. It was the easiest thing ever.

Thank you

Eased the putty knife under the edge of the switch housing and pried it off. Pulled two wires off the old terminals and hooked them onto the new one and reinstalled into the refrigerator body.

bulbs were not burnt out. received the new switch in a few days. watch the short video, was good to see how it comes out. used a putty knife to release the defective switch, removed wires put them on the new one and posed the new switch back in. Not bad Part cost $11.00 7 dollars shipping so for 17 bucks it works great. nice to see what is inside the refer!

I looked it up on the site per Refrigerator Model #. I wanted a confirmation from an expert at this site that I was ordering the right drawer. The part # the expert gave me was different than what I was going to order per my Model #. I'm really glad I waited for the expert reply and ordered that drawer. This is for a rental property, and we are a few hours away from the property. It was less than a minute to pull out the old crisper drawer and slide in the new. Thank You!!!!!

Took everything out of the old one, lined the new one with cloth and put everything back in.

We looked up the problem online with the model number of the refrigerator. We ordered the part and followed the video installation that was sent with the order and was found online prior to purchasing

first confirm that freezer is cold. if is frozen solid it needs to be defrosted. take the freezer items out,take shelf out, bottom cover, 2 screws. then ice maker, 3 screws and unplug wires. then back panel 2 screws. In refrigerator compartment were the controllers are located, look under it you will see 1 hole, insert a flat end screw driver and turn clockwise till it stops. this action will turn on your defroster, also the compressor will stop. is the heater melting the ice? if so soak up water and clean tray, use hair dryer in drain hole to aid in the defrost, check tray under fridge and if its dry keep defrosting. it should take half an hour. now take the flat head screw driver and turn the defrost timer clock wise out of defrost mode a quarter turn or so. the compressor should come back on, soon after the fan in the freezer compartment should also come on. this steps lets you no that the defrost heater works, fan works and drain hole is clear. if its defrosted place parts back in the reverse order. if not defrosted replace heater or mother board. in refrigerator compartment were the dials are located their are 2 screws, one on the left and the other on the right side take them out, the cover will drop down, you will find wiring schematics you will need them to install defrost timer. is timer making ticking sound? if no replace timer. new timer will be different from original so follow instructions that come with it. timer is above were the hole is located. the plastic hold downs will break when you try to take them off, unplug fridge, lift timer out and remove from wire harness. the new timer has a black wire that slips over either 1 or 2 depending on color of wire on the wire harness. check schematics. some silicone adhesive will keep unit in place, ad some into the plastic shaft prior to installation, plug wire harness return wiring instruction along with new one inside of cover, plug in fridge, turn defrost timer clock wise with flat head screw driver making sure that you hold timer from above so it wont move. did compressor come on?. put all paper work inside of cover before installing cover

replaced ice maker with recommended add on kit. easy to replace exact replacement. used this company for washing machine part. parts correct both times.

This was really easy to do thanks to comments posted on the Partselect web site and the instructions included in the package. I removed three screws, unplugged the wire harness using a small screw driver to "unlock" the harness, removed the old ice maker assembly from the freezer, and reversed the process with the new assembly. Saved the valve and other parts for future use. The new unit started making ice within an hour or two. Very cool!

Replaced but drawers are lesser quality to the original drawers. Do not glide open easily

Because of the age of the unit, I replaced all but the wire harness. It was easy to repalce.

Work just perfect

Ordered a defrost timer kit and a Bimetal defrost thermostat clip. I matched the wires but first I unplugged the frig.I cut the two wires on the Bimetal defrost and added the two connectors. All's well that ends well.Problem solved.

Not a repair, only a new part.

I noticed that the refrigerator was having trouble maintaining temperature. Thought it might be time for new one until I found out that a new frig was $5k to $7K. Just happened to notice that the light switch didn't look quite right (was not sitting sqaure to the door). Once I pressed it it came loose. I then realized the the lights were staying on (50 watts of heating). Replaced the switch and the frig started working like new.