10673206300 Kenmore Refrigerator - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- M from Lafayette, IN
- Parts Used:
- W11700559
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver
REplaced ice maker
Replacement was very easy as new ice maker was identical to the old one. Took about 10 minutes.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Robert from Austin, TX
- Parts Used:
- 4387913
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers
Fridge Air On, Not Cooling
Previous issue with this refrigerator and I figure after the Hot summer we've had in TX that it overworked itself this summer in the garage! Caught this one before all was lost as it started it's not cooling cycle on a Sunday. Ordered the identical Relay&Overload from Parts Select, 2 days later I'm back to chilling the beer again! Super service with diagrams and specs. Very glad parts select is around!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Joe from Arnold, MD
- Parts Used:
- WP2315539
- Difficulty Level:
- Easy
- Total Repair Time:
- 1- 2 hours
- Tools:
- Nutdriver, Pliers
power surge killed the fan motor
Removed back panel in the freezer. Removed old fan. Installed new fan and reinstalled back panel.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Laurence from Middleton, WI
- Parts Used:
- W10190935
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Screw drivers
plastic gear broke off - cubes not getting kicked out
removed the three screw holding the broken unit - pulled off the old module.
Before I could install new module I had to loosen some fasteners on ice maker so I could turn shaft to align with new module.
Then push on new unit and three screws. Had tumbling ice in about an hour. My wife thinks I'm a hero. (I am)
Before I could install new module I had to loosen some fasteners on ice maker so I could turn shaft to align with new module.
Then push on new unit and three screws. Had tumbling ice in about an hour. My wife thinks I'm a hero. (I am)
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Julia from Seguin, TX
- Parts Used:
- 8201597
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
There was a pin size hole in the tube.
It was pretty easy to install. The most difficult part was trying to get my hands into the small area to work. I had to use both hands, one to push the release in and the other to pull the tube out. Once I did that, inserting the tube was easy and everything worked perfectly.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Frank from Brookfield, IL
- Parts Used:
- WP2176225
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Broken glass shelf
Took out glass shelf to clean. Shelf exploded into a billion little pieces for no apparent reason. Received replacement shelf the next day (with the 3 - 5 day shipping). Cleaned glass, placed in ice box. Viola!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Greg from Cary, NC
- Parts Used:
- W10190935
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
ice would not fall from ice maker
I ran all the ice maker module tests that I could find online, I tried cleaning the contacts inside the ice maker control module, nothing worked...so I finally decided to purchase a new control module. I had already had the module out and taken apart a few times, so the new one was very easy to install. Just removed the entire icemaker from the fridge, removed a few screws, took off the old module, put on the new one, replaced the screws, re-installed the icemaker in the fridge (it just slides in and out similar to a shelf). And 30 minutes later I heard the first batch of ice cubes drop! And by morning the bucket was nearly full. After two weeks of no ice and trying to fix it myself - the family was glad to have ice again (it was July in NC!). In retrospect, I should have followed the advice I found online and ordered the new part sooner and saved all of those frustrating hours of trying to "fix" the part myself.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Dean from Clermont, FL
- Parts Used:
- 8201597
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers, Socket set
water leak
It was easy, I followed the instructions on the paper and it went well.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- jesse from hacienda heights, CA
- Parts Used:
- W10823511
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Pliers, Screw drivers
Water began to leak under the refrigerator. Source looked like it was coming from control valve suppling water to ice maker and water dispenser.
Followed instructions supplied. It was relatively easy and the parts fit exactly right. Sears wanted twice as much for the part and service would have charged me another $100 to come to my home. I saved over $100 doing the project myself.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Michelle from Richardson, TX
- Parts Used:
- 72017
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Scratches in Surface
This product comes in a bottle with a brush like Liquid Paper. It goes on incredibly easy. A second coat might be needed. I wanted to prevent rust from setting in so I covered the scratches and dings. The paint is a little brighter since my washer is 10 years old but it still looks great.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- gerardo from el monte, CA
- Parts Used:
- WPW10662129
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
compressor didnt turn on
changed the starter connected to the compressor
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- patricia from collinsville, IL
- Parts Used:
- WP2195916K, WPW10421486, WP2195947
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
the door trim was bent and broken and would not hold items in place
I only needed to set the endcap and trim piec es in place, no tools involved
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Joe from Pryor, OK
- Parts Used:
- W10190935
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver, Screw drivers
Following a brief power outage, it stopped producing ice. Harvester was at 6:00 with fingers frozen in ice cubes. Would make a batch if I freed the harvester and jumped the t-stat, but would quit again.
Unplugged refrigerator. Used nut driver to remove small bolt retaining wire cover on right side of ice maker. Removed wire cover, used flat head screw driver to depress side-rail clips. Ice maker slid out, unplugged. Timer module cover pops off easily. Three screws removed the timer module. Installation was reverse of removal. Had ice in less than an hour, bin was full by next morning. If you have a screw driver and know what it's for, this job should come easily.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Anoop from Diamond Bar, CA
- Parts Used:
- WP2166108
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers, Socket set
front roller wheel broke
its not that hard to replace. may need help to tilt fridge on one side so you can get to the bottom to remove wheel.Had to undo all four corner screws/bolts to loosen bottom section and slowly pull out base frame which holds the 4 wheels. this frame is also holding the compressor and fan so be careful.replace wheel and slowly put frame back to position and screw back bolts. pull back fridge to upright position. leave unplugged for a day or two to allow gas to come back to normal level as we had tilted it.plug it back and it works.
thanks
Anoop
thanks
Anoop
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Victor from San Mateo, CA
- Parts Used:
- WP2186494B
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
I broke the old cap trying to turn the filter cc wise.
I installed the new cap on a new filter, which I will install when the old filter needs replacing. No tools required, but it is sometimes difficult to turn the filter cc wise, when replacing.
Was this instruction helpful to you?
Thank you for voting!