10672132100 Kenmore Refrigerator - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- GARY from WEST CHESTER, PA
- Parts Used:
- W10190935
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
No ice
I removed the icemaker. One screw at the bottom and then unplug the electric. Remove the old motor from the face that has 3 screws holding it. Put the new motor in. A very simple job. I now have a full ice bin by the next morning.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- George from Albakurky, NM
- Parts Used:
- 2159061
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Socket set
cut old off the door and put new on the door
took door of the refergarator. Then cut old gusket of and clipped the new one on and then put the back. Done!!!!!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Curtis from Blackwood, NJ
- Parts Used:
- W10190935
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers, Wrench set
The icemaker on the refrigerator had stoped working.
Repair was real easy, I had to remove several screws in the bottom of the icemaker module housing. The unit slide out with no problem there was a wire assembly that hat to be disconnected but this did not present a problem. The old module came out real easy after removing 4 screws and the replacement was not a problem to but in.
Was this instruction helpful to you?
Thank you for voting!
ice maker gears stripped/ bearing & cup assy broken
The bearing & cup assembly was broken and the gears in the drive assy were stripped. Unfortunately I couldn't find anywhere to buy the gears without buying the entire motor assy with the gear box already on it. Cost was up to $85 with shipping but at least it now works fine.
To repair: a 1/4 nut driver will take off screw below ice maker and all you need to do is loosen the 2 screws above the ice maker then push it upward slightly and it will slide off the top 2 screws. Then pull the power connector off from behind the ice maker at the side of the refridge. Then pull straight out and it will slide off the water fill tube. Now with unit out of refridge I took the cover off the front of the ice maker and removed the 3 philip screws. I then pulled the motor/gear assy off from the chassis of the ice maker. I then had to remove the 2 philip screws on the chassis (under the motor/gear assy) to remove the cube maker/element from the chassis. This allowed me to remove the rotating cube spatula bar to replace the filler cup/bearing assy. Then I reinstalled the spatula bar and the 2 philip scews on the chassis to the cube maker/element assy. I then installed the new motor/gear assy to the chassis and installed the 3 remaining philip screws. Put the cover back on the ice maker and inserted assy back into the refridge by first reattaching the power connector and then sliding backward onto the water fill tube and then slipping over the top of the 2 top screws on the refridge. Then I installed the screw below the ice maker and tightened all 3. Presto - repair done in 30 minutes and perfect cubes were spitting out within the hour.
To repair: a 1/4 nut driver will take off screw below ice maker and all you need to do is loosen the 2 screws above the ice maker then push it upward slightly and it will slide off the top 2 screws. Then pull the power connector off from behind the ice maker at the side of the refridge. Then pull straight out and it will slide off the water fill tube. Now with unit out of refridge I took the cover off the front of the ice maker and removed the 3 philip screws. I then pulled the motor/gear assy off from the chassis of the ice maker. I then had to remove the 2 philip screws on the chassis (under the motor/gear assy) to remove the cube maker/element from the chassis. This allowed me to remove the rotating cube spatula bar to replace the filler cup/bearing assy. Then I reinstalled the spatula bar and the 2 philip scews on the chassis to the cube maker/element assy. I then installed the new motor/gear assy to the chassis and installed the 3 remaining philip screws. Put the cover back on the ice maker and inserted assy back into the refridge by first reattaching the power connector and then sliding backward onto the water fill tube and then slipping over the top of the 2 top screws on the refridge. Then I installed the screw below the ice maker and tightened all 3. Presto - repair done in 30 minutes and perfect cubes were spitting out within the hour.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- James from Tomball, TX
- Parts Used:
- WPW10190929
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Screw drivers
The coating on the mold /heater unit as cracked and some broken off and cause the water to drip down in the Ice trace and form large icicles
I just removed the unit and replaced the mold/'heater with the new one and re-installed. It was very easy and didn't have to turn off the refer. or empty the frozen food.
However , there were not instruction that came with the mold/heater unit. I had no problem but other do-in-uselfers may need some basic instructons
Jim
However , there were not instruction that came with the mold/heater unit. I had no problem but other do-in-uselfers may need some basic instructons
Jim
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Diane from Brighton, MI
- Parts Used:
- WP4387503
- Difficulty Level:
- Very Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Pliers
Ice buildup in freezer causing leaking water into fridge section
In my case the defrost thermostat was not the problem. Not worth going through the hassle of checking the thermostat as I would have had to cut it out and test it in another freezer (while the food that was in the freezer was being stored elsewhere). I just ended up buying it and replacing it. So, like I said the defrost thermostat was NOT the issue. I ended up getting a drain tube heater strap, and have been keeping my eye on the fridge. It hasn't been long enough to say the strap fixed the problem, but all indications are pointing to that being the case.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Louis from BASKING RIDGE, NJ
- Parts Used:
- W10190935
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Screw drivers
Ice maker clicked CW and CCW, but did not make ice
Replaced the control of the ice maker assembly.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Roy from KAUFMAN, TX
- Parts Used:
- 2159061
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver
Door would pop open. I cleaned gasket made sure nothing in the way of door. Gasket was cracked top and bottom it worked better but the seal was not good.
Did just like the video showed took doors off daughter helped take off doors so easy put door on blanket. My daughter 38 went to town putting it on just watch the corners so easy two days after installation the door seals great. You can do this.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Michael from CHICAGO, IL
- Parts Used:
- 2159060
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver
Defrost drain clogged with ice
Replaced gaskets on both doors. Followed the online video link that came with emailed receipt. Worked exactly like demonstrated in the video.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- JAMIE from HANOVER, PA
- Parts Used:
- W10190935
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver, Screw drivers
icemaker wasn't making ice
i followed the online instructions on how to take the icemaker apart, which were very easy to follow. Once the new part arrived it plugged right in and a few steps later it was back together. within the hour we were hearing the sound of ice dropping into the tray. thanks for all the help this definitely saved us money and hopefully we get many more years out of this icemaker.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Sean from Lancster, CA
- Parts Used:
- W10190935
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver, Screw drivers
Ice maker stopped making ice
Removed the one screw holding the unit in place in the freezer and pulled it out. Removed the 3 screws that hold the motor in place on the ice maker. Replaced the motor unit, replaced the 3 screws, and re-installed the ice maker.
Sears wanted $170 for labor for the 10 minute job, plus $130 for the part, which I got here for $65.
Sears wanted $170 for labor for the 10 minute job, plus $130 for the part, which I got here for $65.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Linda from ROCK ISLAND, IL
- Parts Used:
- WP2314549
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
My crisper cover frame broke
It was very easy just took out the old broken crisper cover frame out and put in the new one. Simple as that.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Kevin from SWANVILLE, ME
- Parts Used:
- W11338583
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Freezer Bulb failed
Unscrewed bulb from sock .
Replaced with new one . Now working
Replaced with new one . Now working
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Barbara from FERN BCH, FL
- Parts Used:
- WP2218118
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Broken butter door
I popped the new one right in.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- James from BUFFALO, NY
- Parts Used:
- WP2218132K
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Replace meat draw
Came on time, just slide in
Was this instruction helpful to you?
Thank you for voting!