25354364402 Kenmore Refrigerator - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- HUNG from CARSON, CA
- Parts Used:
- 5303918455
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers, Socket set
Right door makes loud poping sound when open and close
I followed step by step instruction in the hinge kit; Replacing the old hinge with a new hinge and two new plastic cams in the kit. The kit hinge has an adjustment to level the right door with the left door. Everything is done in 20 minutes for a senior guy like me. Very easy.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Karl from Bellaire, TX
- Parts Used:
- 240356501
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Support rail broke
I recieved the part within 48 hours. I snapped the part in place and I was done in seconds.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Bob from Gilbert, MN
- Parts Used:
- 5303918214
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Screw drivers
Refridgerator freezing food
Unplugged fridge from outlet. Removed rear panel on freezer side. Removed defrost thermostat from tube and cut wires. Installed new thermostat by matching color coded wires and crimping with supplied connectors and snap back on tube. Reinstalled panel and shelving.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Robert from Louisville, KY
- Parts Used:
- 242252702
- Difficulty Level:
- Really Easy
- Total Repair Time:
- More than 2 hours
- Tools:
- Pliers, Screw drivers
water valve failure
removed rear cover, removed screws, diconnected water line connections, cut off old water line connection, installed new compression water line connection, replace screws in water line housing, replace rear cover.
worked fine
worked fine
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Christopher from Middletown, CT
- Parts Used:
- 5304469407
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Screw drivers
Motor had failed due to ice ejector frozen to tray.
Removed the ice maker. Took off the cover and proceed to remove the motor. The only trick was to dis-assemble the electrical connector to replace the wires. I chose to do this rather than splice the new motor into the existing system and it was simple with a little patience.
Easiest repair to make and half / third the money for a new ice maker. The in-laws have ice again (it was over a year).
Easiest repair to make and half / third the money for a new ice maker. The in-laws have ice again (it was over a year).
Was this instruction helpful to you?
Thank you for voting!
Rust had corroded Front Plate and Drive Blade
Installation was completed by following the online Parts diagram. Had to completely remove all parts, including the blades in ice crusher, and re-assemble. Glad the online diagram was clear and easy to read.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Tina from Baroda, MI
- Parts Used:
- 240356501
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
My son pulled on the meat pan & cracked the right support.
The old support just unscrewed & then the new one screwed right on with two screws.
Was this instruction helpful to you?
Thank you for voting!
crisper drawer supports broke
The parts supplied were made to fit. The hardest part was getting the original broken tabs out of the internal walls of the fridge with out damaging the internal insulation. I punched the center locking pin through completely, dug out the broken tabs and then reached into the hole with a dental pick and pulled out the center pin. The new parts fit perfectly and with a plastic mallet, tapped the new locking pin into place.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Matthew from Wyomissing, PA
- Parts Used:
- 240359001
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
The freezer door bin broke while overstuffing it.
Well...The freezer door bin broke while over-stuffing it with frozen deer jerky. I called my local repair shop and they quoted me what was above retail for the piece...I checked online liked the prices and felt confident to buy from parts select. I bought on a Saturday and selected the slowest shipping (I think 5 days). I got a 'notice' it shipped on Monday and had it Tuesday when I got home from work. Excellent experience.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Robert from DeFuniak Spgs, FL
- Parts Used:
- 5303918344
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver
ice maker motor shorted out
loosen 2 screws
unplug connector
remove
replug
replace
tighten 2 screws
done
unplug connector
remove
replug
replace
tighten 2 screws
done
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Sandra from Alto, NM
- Parts Used:
- 240457701
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
plastic closer plate broken
First removed food from the refrigerator door.
Second removed plastic cover plate and metal plate assembly from top of door.
Third lifted door of metal pin on bottom.
Fourth removed broken closer plate and replaced
with new closer plate.
Set door back in place.
Re secured the metal plate and plastic cover plate.
Replaced the door shelves and food. DONE.
Second removed plastic cover plate and metal plate assembly from top of door.
Third lifted door of metal pin on bottom.
Fourth removed broken closer plate and replaced
with new closer plate.
Set door back in place.
Re secured the metal plate and plastic cover plate.
Replaced the door shelves and food. DONE.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Dennis from Crossville, TN
- Parts Used:
- 5303918455, 240328201
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers, Socket set
Snapping noise from bottom of refridgerator door bottom hinge.
First I looked up and called Fridgedaire. They were absolutely no help at all. No diagrams and no intelligent help.
When I found your site there was an IPB (Illustrated Parts Breakdown) diagram that helped me find the parts that I suspected as being the problem. When I found them and added them to my cart I found several comments from people who had the same problem and the same remedy to the problem. I ordered the parts, I could have got away with just replacing the door closure bearing, but I figured that the prudent thing to do while ordering parts and disassembling the door was to replace both.
I was extremley pleased with the parts service as within three days of ordering the parts they were at my home and the repair was completed.
The repair was very easy. Removed the items from the door storage, removed the upper hinge pulled the door, removed the door stop, replaced the door closure bearing reinstalled the pieces and then reinstalled the door. Piece of cake. Spent more time getting the tools together and emptying the items stored on the door then replacing the parts.
When I found your site there was an IPB (Illustrated Parts Breakdown) diagram that helped me find the parts that I suspected as being the problem. When I found them and added them to my cart I found several comments from people who had the same problem and the same remedy to the problem. I ordered the parts, I could have got away with just replacing the door closure bearing, but I figured that the prudent thing to do while ordering parts and disassembling the door was to replace both.
I was extremley pleased with the parts service as within three days of ordering the parts they were at my home and the repair was completed.
The repair was very easy. Removed the items from the door storage, removed the upper hinge pulled the door, removed the door stop, replaced the door closure bearing reinstalled the pieces and then reinstalled the door. Piece of cake. Spent more time getting the tools together and emptying the items stored on the door then replacing the parts.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Myron from Tumwater, WA
- Parts Used:
- 242252702
- Difficulty Level:
- Easy
- Total Repair Time:
- 1- 2 hours
- Tools:
- Nutdriver, Pliers, Screw drivers, Wrench (Adjustable)
Ice maker malfunctioned
We followed the video instructions and it went fairly smooth. After turning off the water at the street we found that the faucet at the wall had it's own "on/off" valve. When finished, we turned on the power and heard the gears going through their revolutions, but no ice was made. We waited 24 hours and still no ice. I removed the cover on the ice maker and adjusted the amount of water to see if that was malfunctioning. Still no ice was created. Waited another 24 hours - nothing. Waited another 24 hours (the site said that sometimes the ice maker would take time to reset itself) - nothing. Then on the fourth day after changing out the triple water valve we heard water being dispensed and later that day it put out the first ice in weeks. Another hour later another batch of ice cubes were ready and deposited into the bin. Since that time, we have had a full bin. I moved the set screw back to it's original setting because a little too much water was being delivered. The cubes weren't separating to individual cubes. That cleared up the problem. This was easily completed - we recommend others do their own work. Just be patient for the system to reset itself.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- ROWENA from WIGGINS, MS
- Parts Used:
- 241685101
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers, Socket set
The drum ice maker broke in half so it couldn't dependent the ice.
I had removed the housing that the drum was in and taken the screws out to get to the broken drum. I removed it there was a set of 6 blades that crushed the ice that had to go back on the same order when I removed these I put them on a piece of wire in the order they came off (so I would get them back I the correct order). Then I reversed the order and reassembled it in the opposite direction . It was fairly easy to do. I'm a 68 year old disabled woman so if I could do it I'm sure you could to. Good luck. It cost me $14.00 if I had bought the whole assembly it would have been $150.00. So it was well worth my time and effort.
Was this instruction helpful to you?
Thank you for voting!
The basket hanger is plastic and the rack tips of the basket hanger are even more delicate. Replaced basmet hanger no problem. They were expensive i.e. $70.
Unscrew 4 screws . Remove broken basket hangers. Install new basketo hangers. Screw in 4 retaining screws...
Was this instruction helpful to you?
Thank you for voting!