1067678660 Kenmore Refrigerator - Instructions

Remove one 5/16 screw from top hinge cover plate. Trace outline of hinge on top of refrigerator with sharpie, so you will know where to put hinge back. Remove 3 5/16 screws from hinge. Lift door up out of bottom hinge, place on table to be able to work on. Remove one 5/16 screw and upper cam piece from bottom of door and replace with new upper cam piece. Remove one 5/16 screw and lower cam piece from bottom hinge on refrigerator. Replace with new lower cam piece and one screw Set door back in place and reattach top hinge with 3 screws adjust refrigerator door as needed for a nice even gap between freezer and refrigerator doors. Tighten screws down and put hinge cover back on with one screw.

I removed the switch housing (4 screws), replacing the switch in the housing was a snap. It took 5 minutes, cost $8 and light works like new!

Why didn't I order this part and do the repair earlier? Very simple.

Removed the ice brucket,
Removed the light shield by releasing one screw using a nutdriver.
Replacing the bulb and reinstalled the light shield.

Your web site is one of the best and most helpfull service sites I ever used. Just wish that in the future you will ship parts overseas.

remove door, replace cam, replace door

easy - remove the door, replace th part, put back the door

Very simple fix, remove 3 screws, two connectors to the old switch

Simple read about three of the other peoples repairs,did the same and (PIECE OF CAKE)
Only problem ordered the cam kit with shipping over # 18.oo and only needed two pieces to do the job. Should have ordered just the two cams and saved a lot of dough.
But done and over with a happy camper (WIFE)

use kitchen knife to pry out. replaced switch assemble and pressed back into place. Could not have done this with out help from previous customers. Thanks

All I had to do was remove the screws at the top of the refrigerator door that hold the top hinge and once that was done I lifted up on the door and it came off. I then flipped the door upside down and was able to replace the door cam on the door and the other cam on the bottom hinge of the refrigerator. Once replaced, I put the door back on and put the screws back in on the top hinge of the refrigerator door. Works great now!

I hand screwed the fill tube into the water tube and stuck it into the freezer hole. I screwed the fill tube to the back of the refrigerator.

Thanks so much! You saved me a bundle!!

I got the product very quickly. (thank you) Looked at online instructions that were quite vague. Pulled plug.Removed the holder for the fan motor slid it out to see what I had. Removed the mounting screws (3) and slid the motor an fan blade out. I made a cut between the wires and marked the "top" wire to motor to be sure to spin in right direction. Removing fan blade hold down clamp was NOT explained at all but I noted that the shaft on the motor was threaded, so I used pliars and held the shaft white un-screwing clamp. I cleaned the fan blades with degreaser and scraped edges of opening on holder opening. Make sure to use ALL the NEW parts included with this kit when re-installing. They send them for a reason. When slpicing and connecting wires it is a 50/50 shot if you don't mark before cutting. You can connect and try plugging fridge back for moment and make sure it is blowing OUT. Put everything back together and after turning DOWN the thermostats twice, fridge is back to usual. Ice maker is cranking out ice and outside case is cool to the touch.

Note: This can be a DIRTY job especially with 4 dogs in house. Fir and grease don't mix well

figured out the condenser fan was kaput. Tried WD, worked for several days then gave out completely. Took off back of fridge and trained small fan on compressor while I ordered new condenser fan. The swap was easy, undid the housing bolts, stripped off the connector, reconnected and voila! works perfect.

1, Removed heavy items from door bottom two shelves.
2. With door closed, prop up door with 2x4 boards and wood shim to support door weight.
3. With nut driver, wrench or socket wrench remove lower door hindge.
4. Removed worn plastic door cams and shim.
5. Install new door cams and shim.
6. Install lower door hindge and lubricate cams with silicone grease.
7. Remove wood bracing.

First I removed all the screws from the back cover.
2nd removed fan nut and fan blade
3rd removed fan bracket
4th I traced wire to the condenser and disconnected wires from wire nuts.
Installed existing fan brackets to new motor kit
then reconnected wire nuts to new motor cord
Reinstalled fan nut and blade,
reinstalled cover, plugged it in and BAM .WORKS PERF!

I removed 7 screws hold the heavy cardboard cover on the rear of the fridge. The dificult part was taking the screws that hold the 3 fan motor braces on the fan out. After that it was a matter of making the wire conections and putting it back in. I did not have enough room to laydown to do the work, If i had it would have been a lot easier to see the screws that had to be removed. All in all an easy job, and the part was a perfect fit.