59672253202 Kenmore Refrigerator - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Linda from Johnson City, NY
- Parts Used:
- D7824706Q
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
leaking ice maker,big chunks ot ice were forming and had to remove them 2-3 times a day
removed old ice maker by taking out a couple of screws in the back of freezer,when new ice maker arrived i saw that it didn't have the same hose apparatus as old one so I easily took apart old one then took apart new one and switched them out-very-- easily done for a 61 yr old lady I might add-- also had to reinstall ice maker arm off old ice maker as new one does not come with one Then installed new ice maker in freezer I am very very pleased,sure saved a lot of money doing it my self
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Mike from Milwaukie, OR
- Parts Used:
- 12001937
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver
Auto frost not working correctly
My Freezer would only auto defrost occasionally and I first thought it was the defrost timer. But after reading posts on this website I looked deeper and found that my Defrost thermostat was bulging out. That didn't seem right just by looking at it. I read an earlier post and figured that must be it. I received the part and did the repair in about 15 minutes just had to cut two wires and reconnect with wire nuts and clip thermostat back onto the copper tube. Works perfectly now!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Winston A from Brooklyn, NY
- Parts Used:
- W11384469
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers
Raplaced switch
Repair went well,took about five to ten minutes to disconnect the power from the fridge removed the defective switch installed the new one ,reconnected the power,,,and Let there be light and there was light!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Daniel from POPLAR BLUFF, MO
- Parts Used:
- WP67003000
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Pliers, Screw drivers
Fridge and freezer were not getting cold. Clicking sound when compressor shutting off.
We noticed that items if the fridge portion of the refrigerator were starting to go bad before they should have and that the items in the freezer were not solidly frozen at times. I actually had two parts that needed to be replaced on my refrigerator, the relay assembly located near the compressor and the temperature control switch located in the freezer section. My fridge was making a clicking sound several months before it stopped working. I used the symptoms link on the website to help me locate what part might be the culprit and found the relay switch near the compressor bad and replaced it. A few days later we still had the same problem of both the fridge and freezer not being cold enough. Turns out the temperature controller in the freezer was just barely turning on when it would get warm enough in the freezer section. Once that part was replaced the refrigerator worked like new. It took me a while to find both problems since one was masked by the other but the website was a great help in finding both and getting the parts to fix everything.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Donald from OMAHA, NE
- Parts Used:
- 12001937
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Screw drivers
Fridge warm, freeze cold.
Thermostat kit it only had one connector. Fortunately I had a small wire nut that I used on the other wires.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Aliki from Miami, FL
- Parts Used:
- WP628356
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Fill cup broke.
Very easy to order from parts select. Took seconds to replace.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- DANA from ASHTABULA, OH
- Parts Used:
- WPW10671238
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Center Crisper Rail Broke Off At One End--Drawers Would Not Slide And Hang Right.
Very easily removed top shel glass above crisper--removed old rail by lifting up--and place new one in slots provided---simple!! Part was delivered in less than 3 days-------very fast and cheap !!!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- LYNN from PANORA, IA
- Parts Used:
- WP67003753
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
No ice
replaced inlet valve per insert with part, easy
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Daniel from DAVISBURG, MI
- Parts Used:
- D7824706Q
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver, Screw drivers
Ice maker stopped making ice
Remove 1 screw under ice maker. Gently pull downwards to unhook ice maker. Disconnected 4 pin wire connector. Remove and set aside the cover and wire loop you will need on new ice maker. Reverse the steps to install new maker. Once new ice maker is installed you will have to wait 2-4 hours for ice. There is a thermostat that will need to reach 10 degrees F to operate.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Allan from Tucson, AZ
- Parts Used:
- WPW10671238
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Broken center crisper rail
Total time 10 minutes. 9 minutes to clear out the food and 1 minute to install the part. Installation was self evident and could have been done blindfolded. Part just snapped in.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Daniel from LAKE CITY, FL
- Parts Used:
- WPW10436250
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Freezer freezing up. Frost everywhere.
Old gasket pulled of easily with no tools. New gasket was placed on floor and heated with blow dryer to straighten. Then installed new gasket by pressing in with my hands. Noticed that the old gasket was hard and not flexible. All was great. Fit perfectly. No frost after a week. Happy.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Karen from Riverside, CA
- Parts Used:
- WPW10671238, WPW10568041
- Difficulty Level:
- Very Easy
- Total Repair Time:
- 15 - 30 mins
Both pieces were broken.
Just replaced old with new. The glass shelf was good so just moved it to the new pieces. Everything fit perfectly, thank you.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- frank from NORTHRIDGE, CA
- Parts Used:
- WPD7813010
- Difficulty Level:
- Very Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver
Ice maker not producing ice
The parts were very easy to replace, however I am still without ice and cannot figure out why. I have ohm tested the contol unit and everything works fine, I am able to jump it and turn on the motor and water fill valve. Any suggestions?...
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Ida Mae from MEDLEY, FL
- Parts Used:
- WPW10436250
- Difficulty Level:
- Very Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Door Gasket had a tear in it.
To repair the problem,I ordered a new gasket. Once I received the gasket, I laid it flat on the floors and hot the blow dryer and blow out the creases in the gasket. I then took off the door by removing the four screws from the door and rest the door on the table. I then removed the old gasket and replaced it with the new one. It took about 15 minutes. My frig. Stop freezing up.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jane from Albuquerque, NM
- Parts Used:
- W11384469
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Screw drivers, Socket set
lights wouldn't come on/work in refrigerator
Referencing the info/schematics you have on your website, I unscrewed/unattached top-front panel (carefully), from behind the panel you have to detach the wires (2) from the switch, pushed "in" the switch to remove, put in new switch and attach wires to test BEFORE remounting panel. Tada!! Thank you PartSelect! You saved me at least $80...would have been at least $100 to have a repair person come to the house!
Was this instruction helpful to you?
Thank you for voting!