1068698632 Kenmore Refrigerator - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Gregory from Virginia Beach, VA
- Parts Used:
- WP2155013
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Screw drivers, Socket set, Wrench (Adjustable)
Dryer made loud intermittant humming sound after 20-30 minutes of use
Unplug Dryer. Remove 2 5/16in hex screws from lower panel and remove panel.Remove 3 5/16in hex screws attaching lint duct. Remove 8 1/4in hex screws attaching blower housing. Remove 2 1/4 hex screws attaching thermostat to blower housing. Using adj. wrench on back of motor shaft nut to hold, loosen fan assy. w/ 7/8in socket. Remove 3 5/16in hex screws holding fan housing to motor mount. Remove 2 5/16in hex screws holding housing and motor mount to base floor. Push belt pulley wheel up enough to loosen belt and take off rear motor pulley. Motor w/mount can be slid out bottom for replacement [wires are layed toward front].Using 6in flat tip screw driver press down to unlock front & back motor bushing holddown clamps. Pinch electrical wire connector ends to pull off old motor. Remove and Install new motor, reversing steps. Belt replacement [suggested w/new motor] requires removal of 2 5/16in screws to lift/remove door w/front panel [disconnect door switch wires upper right rear corner].Remove 4 5/16 screws holding front bulkhead. Once bulkhead is pulled up and off, allow front end of drum to sag and rest IN PLACE [removal not required to slip old belt off and install new belt]. Note belt location point around drum. Slide new belt on. Reinstall bulkhead and panel/door [Don't forget door swich wires]. Adjust belt into position and push spring-held belt pully up to allow looping of new belt around rear motor belt pulley. Complete w/hand turning of drum to ensure belt is aligned and feeding properly. Reinstall lower fan housing/covers/thermostat,etc removed for motor installation.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Atlee from Jupiter, FL
- Parts Used:
- WP2149705
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Screw drivers
broken light switch
Figured out You have to pop off the cocer than remove the 1/4 hex head screws only not the philips ones
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Carl from Crete, IL
- Parts Used:
- W11581579
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers
Freezer shelf falling off
One of the front studs was broken off. I had to use pliers to pull it out (kind of tight). Then I inserted the back and front holders and layed the shelf back in. Total time...10 min
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Mary from Pelham, NY
- Parts Used:
- 4386774
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
the front wheel broke
First I had to tilt the refrigerator on wood on the supports under the refrigerator, the wheels were easy to get to then I unscrewed the old ones and replaced them with the new better wheels. The old ones where plastic.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Ted from Magnolia, TX
- Parts Used:
- 4386774
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Socket set
Broken wheel under fridge
Replaced both since they came as a set. The only way it could have been any easier is if I had the wife do it. She had the remote this time. (•¿•)
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Raymond from Victorville, CA
- Parts Used:
- W11581579
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Broken bracket
Replaced broken shelf bracket
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Richard from Copperas Cove, TX
- Parts Used:
- 4386917
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
plastic end cap clip broke
removed retaining bar removed and replaced end cap and reinstalled retaining bar.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Michael from Bloomingdale, NJ
- Parts Used:
- 4386917
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
End cap was broken
Took out the broken part and replaced with the new one..Simple enough and we had been living with a taped one for yrs...
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Denise from Sparks, NV
- Parts Used:
- 4386917
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Broken bracket for door shelf
Just replaced the old piece with the new. Simple and easy.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Ronald from Colorado Springs, CO
- Parts Used:
- 4386917
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
broken door shelf
Well the part and repair was so easy my wife did it and is very proud of herself
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jeffrey from Little Falls, NY
- Parts Used:
- W10822278
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver
Noisy defrost timer
Part # had been replaced with another timer. Original timer had 2 wires coming out of it. Replacement only had 1 wire. Instructions showed 2 options for where to place the wire. I chose option 2 and I guess I was right. Installation took less than 15 minutes and refridge is back to normal. (Quiet)
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Anne from Wall, NJ
- Parts Used:
- 4386917
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
broken end cap
snapped in the new end cap and snapped it into the fridge. I shouldn't have waited so long to order the part. it was cheap and easy to do
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Kathy from Fort Lauderdale, FL
- Parts Used:
- 4386917
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
broken shelf
I put the end caps on the shelf bar and popped them into the slots on the refrigerator door. Very easy.
Good experience ordering from PartSelect. Glad I could make repair with minimal expense.
Good experience ordering from PartSelect. Glad I could make repair with minimal expense.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Patrick from Sun City, AZ
- Parts Used:
- W10822278
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Screw drivers
The refridgeror side was not cold enough
it was a simple repair once I located the part I had to replace . I really like your speedy delivery of the part I needed Thank you Pat Crotty
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Albert from Dunmore, PA
- Parts Used:
- W11745278
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Socket set
replace hinge bracket on fridge door
taped the door shut ,measured a block of wood and stuck it under the door for support.....unbolted bottom hinge,slipped on hinge bracket and reassembled.no muss no fuss.
Was this instruction helpful to you?
Thank you for voting!