2538089 Kenmore Refrigerator - Instructions

Loosened 2 screws, lifted icemaker brackets off of loosened retaining screws, unplugged electrical connector from the icemaker.
plugged in the supplied jumper harness & connected to the new icemaker, hung it on the loosened screws, secured the 2 screws.
Dranke beer & listened to my new icemaker rock & roll.
No further problems, Frigie like new.
The price was the cheapest I could find. $78.00 total including shipping.
A little girl could replace this unit.

The service man that I hired to fix my Ice maker removed the broken one. This is how I saw how easy it was to install. When the new one arrived all I had to do was plug it in then tighten 2 screws with the right size nut driver. This was the hardest part of the install havng the right tool for the job. Now I have Ice!

The repair took only 5 minutes. I removed the ice bin, which just slides out, then loosened 2 screws at the back-top of the ice maker. I then unplugged the broken ice maker, removed it, put in the new one, re-tightened the screws and plugged it in. It was making ice within an hour.

The repair was a simple swap of icemakers with a 1/4" nutdriver. I didnt get the first unit sent after 7 days, so I called PartSelect. They were very courteous and understanding. My icemaker arrived within 12 hours of my phone call! Excellent!

The screws holding the ice maker in place were backed out about a turn and a half or so. The icemaker was raised about 1/2 inch to clear the bolt heads. The icemaker was extended just enough to access the wiring harness connector. The connector was released, and the ice maker was removed. The replacement unit extension was unneeded. The wiring harness connector was attached, and the wire was wire-tied out of the way. The icemaker unit was placed over the screw heads, rested in place and the screws were tightened (only snug). Easy-peasy!

was very easy. just ordered a new ice maker which was delivered in a few days. The installation was so simple. Just plugged the new ice maker in and hung the unit on the 2 screws. And then tightened the screws with a 1/4 in nut driver.

I watched the video and did the same thing on mine and now it is working fine

According to the online video instructions.

1-Unpluged the refrigerator 2- removed ice cube tray and some food( Placed in cooler )3- unscrewed the two screws holding the old unit lowering it and unplugged it. 4- Had to loosen the cooling coil to get to the pass through hole in the back and pulled the old wire out. Connected the wire adaptor to the old connectorand to the new ice maker. At this point I couldn`t pass the new plug through the back so I strapped it out of the way and installed the new ice maker using the two screws from the old one. Adjusted the fill adjustment and turned it on. Cubes in about 4 hours.

This would have been an easy repair, but I bought the Frig from Lowes and I think they added the icemaker. The replacement icemaker uint has a plug on it for easy replacement. My frig was hard wired so I had to cut off the plug and splice the wires. Not a real big deal but a small work space.

I needed one with the adapter. I installed it and there was ice in the tray the next morning...no problem

put in a new one

Took less than 10 min to install following the inclosed instructions. At first it was not making enough ice to make me happy so I set the temp. a little colder in freezer. Now making ice like crazy. Works better than the old one ever did. Very happy with the new replacement.

I followed the video that came with my email receipt but i had to use the extra electrical adapter, there is no where to put the extra wiring so it is hanging next to the wall. I was glad I didn't have to unplug the fridge. just kept the wire up so no water would come out. It took several hours to start working and it doesn't make as much ice as the old one, but at least it works. It was a very informative video. Thanks

first replaced dual solenoid, then ice maker. still not working. going to chase electrical next