59650392990 Kenmore Refrigerator - Instructions

I removed the panel to gain access to the condenser and found it to be a solid block of ice. I ordered the 2 parts, I suspected and they arrived in 3 days. I replaced the parts and let it run for 48 hours. All is well and the frige gets colder than before.

Removed the 2 screws holding the light bulb shield, then the 4 uolding the metal panel. Unplugged the olw door switch and replaced.
reassembled the pieces.

Watched video. Unplugged refrigerator and popped out switch. In plugged connector and pushed switch in place. Plugged in refrigerator and the light worked

The repair was simple. Just like the video

proped up frig, loosened screws, cut pin, installed rooler w/ new pin, rounded pin end, reistalled, lowered frig...everyone happy, thanks again partselect.

Followed video and used vaseline to lube as suggested by other review.

First I removed the two screws that hold the timer cover in blace, then I removed the the two screws that hold the timer onto the cover. I was then able to unplug the timer, and reverced the process to re-assemble the timer. Unfortunately.....replacing the timer, did not solve the problem. My refridgerator still freezes up every other day or so. It will eventually thaw, and work for a few days, but then freezes up again.

removed old ice maker by taking out a couple of screws in the back of freezer,when new ice maker arrived i saw that it didn't have the same hose apparatus as old one so I easily took apart old one then took apart new one and switched them out-very-- easily done for a 61 yr old lady I might add-- also had to reinstall ice maker arm off old ice maker as new one does not come with one Then installed new ice maker in freezer I am very very pleased,sure saved a lot of money doing it my self

The defrost circut stopped working which caused the coils to frost over stopping the blower and freezing the water line. Take everything out of the freezer, remove lower back pannel held in by around 8 screws inside the freezer. The thermostat was attached to the upper right coil. It clips on to the coil. Wires attach to the fan and defrost heater. A pair of wires runs out through a hole. These wires are to measure thermostat. It will read 0 ohms when frozen. Rremove and replace the thermostat. The defrost heater should read around 25 ohms. Remove the bottom grill. It pops off. The box in the middle houses the defrost timer. Remove the 2 screws holding the box to the chasis and then remove the defrost timer screws... Before buttoning everythigng up, plug the fridge in to the power and wait for about an hour. The fan in the freezer just above the coils should be running and circulating cool air through the fridge and freezer. Depending on how long your freezer was unplugged, the water should be thawed enough to dispense water again.

This was the third icemaker replaced since January 1999. Improvement need to be made in the design of the icemaker so that more than 2-3 years of life is available.
The most difficult part was disconnecting the power plug in the back of the icemaker. You must squeeze the upper and lower tabs together and pull out at the same time to disconnect. Once this is done, take out one nut head screw, lift up on the icemaker and remove from the hanger. Be careful that you don't break the plastic tabs on the hangers. Replace new icemaker in reverse, feed water supply where it must go in the back, resnap onto hangers, replace the nut head screw and snap in the power plug. It took about 2 hours before the icemaker began making ice. It has been working fine ever since. PS. I saved about $200.00 over having a repairman come in and replace the unit.

Removed pin holding the wheel along with leveling screw. Put new wheel in place, replace pin and screw. Done...very easy.

First took the shelving unit and deli drawer out. Then removed the screws that were still attached. Took off the broken frame and replaced with the new frame. Put the screws back and put the unit back in the refrigerator.

Removed the 3 screws that hold the ice maker in place and remove the cover and level wire. Put the cover and wire on new part and install the 3 screws. Had ice within 1 hour. A very easy job for the do it yourselfer. Suspect the heat coil that melts the cubes was not working in the old unit and cubes stayed in the tray.

I replaced the defrost timer, and then the defrost thermostat. I diagnosed these two items because it would get cold/freeze great for about 12-24 hours and then would start to warm back up. I pulled the cover off that covers the evaporator coil and found it to be frosted up. This told me that the defrost timer probably wasn't working properly. Decided to replace the defrost thermostat while I was in there as a precaution. It was much much cheaper than having to replace a side by side!!

Reassembled auger assembly to new ice bucket with new screws. Fairly simple and straight forward.