36348047896 Kenmore Refrigerator - Instructions

First I removed the two screws that hold the element in place. I then pulled the element out about 3 inches and disconnected the two wires..

Remove the top cover above the door by lifting it slightly and pulling forward. I used a mirror to make sure that there was nothing in the way of accessing the switch from above. I used a blade screwdriver to press against the switch retainer on the topside, while GENTLY prying from below with another blade screwdriver to get the switch dislodged. Once the retainer was past the opening, I wiggled the switch downward and then rotated it to the left when the rounded top right edge of the switch was visible. This allowed the wiring to the connector to pass thru the hole. I pushed the wiring from the top and pulled from below to get the connector below the opening for the switch. I then unplugged the switch, plugged in the new switch and reversed the removal process feeding the connector thru first then rotating the switch to the right to get the rounded edge of the switch thru the opening, then pressed the switch up into the opening until it snapped into place. Total time less than 10 minutes.

Pop out switch, pull wires, attach wires to new switch and pop back in. Easy smeasy!

I ordered the part, within two days we had received it. My husband put the part in and I really don't know what he used doing so. All I know is that the light works now and we don't have to use the flashlight. Thanks a lot.

with a jewelry screwdriver I pried the lock tab in and pulled switch down carefully, the hardest part was that the power wire connector was stuck on good but the pliers and the jewelry screwdriver was its match for a bout 5 minute for one connection a simple pull off prong connection. After the wire connected back to switch it popped back in SNAPP

Took out the light sockets, plugged in the new ones. I found the manual on line to find the part numbers. Parts select parts were perfect

Easy repair. No need to remove the door. Simply prop up the door with blocks or books - remove hinge and riser assembly - replace with new parts. Total repair time about 15 minutes. Tools needed only an open end wrench.

The repair is pretty straight forward it is the preparation that takes time.
The food in the freezer portion of our side by side began thawing. We tried adjusting the temperature level to colder but to no avail. When we started emptying the freezer compartment I noticed a large amount of frost/ice at the back.
I turned the control to off and began defrosting the freezer using my wife's hair dryer. :) Once the outside layer was defrosted I removed the panel covering the coils. They were packed solid with ice and took over 30 minutes to defrost. Be sure to use a pan or container to catch some of the water because the catch pan under the refrigerator isn't large enough.
Once everything was defrosted I removed the heater tube assembly (at bottom of coils)it was a glass tube with a coiled wire element inside. The element had shorted out and the tube appeared black in that area.
I replaced this single tube heater with the double tube recommend on the partselect.com site. This required re-routing one of the wires and splicing in the plug/wire assembly contained in the repair kit.
Simply followed the instructions, reassembled everything and turned the control back on. No more problems. A very easy repair for anyone mechanically inclined and who owns a few basic tools.

I found the frig not cooling as good as it used to and did some research on the net and found some common failures. I started with the easiest test and ohmed out the defrost heater and also noticed it had blackened spots on both ends of element. The ohm reading confirmed it to be open. Replacement was easy for a "diesel" mechanic so basically anybody that can follow directions should be able to replace thiers as well.

Removed 2 screws replaced new part very easy

First I pulled the door up to the top hinge and propped it up with phone books. Secondly I used a nutdriver with an 8mm attachment and removed the bottom hinge. Thirdly, I removed one screw from the bottom of the door with a socket and 8mm attachment and removed the broken cam riser. Being careful as to take note of how the cam was positioned. I then attached the new cam riser to the bottom of the door, attached the bottom hinge to the refrigerator, making sure the pieces (cam riser and plastic on bottom hinge) matched up and after everything was tight, removed the phone books. Remember to first remove the vent on the bottom of the refrigerator and it is much easier to maneuver the door if you empty the contents on the inside. Very easy, I am not very mechanically inclined and this is the first job that I finished in the amount of time as stated. Also, do not chance just the riser as both pieces will be worn. Hinge assembly comes with all you will need.

First I removed glass shelf on top of rail. I then removed the two screws holding rail to refrigerator side. Next I installed new rail using same two screws. Finally I replaced glass shelf on top of rail.

After reading about what others had done on PartSelect, I decided to order the defrost heater and bracket assembly. When the parts arrived (very prompt) I removed the back panel of the freezer. Ice was covering the coils, so I took a hair dryer and melted the ice. Then I removed the defrost heater and replaced it with the new one. Very easy; only a couple of screws on the back wall to remove and one on the heater itself. Anyone can do it. I had called a repair service, and they wanted $75 just for the service call. I probably saved at least $100 by doing the job myself.

took 2 philips screws out,took off rail,and then nreverse.these steps,

Really simple, I used a can of soup and a small piece of wood set under the door, and tapped it tight with the hammer to hold it in place while I removed the hinge. Two bolts at the bottom and two under the door itself. Installed the new hinge set, bolted tight and removed the shim.
The whole thing took less than 5 minutes