3638502510 Kenmore Refrigerator - Instructions

Emptied the drawer and removed it. Then took off the old slide rail. Then I got some hot soapy water and cleaned the walls of the refridge while I was down there and had everything out. I then installed the slide rail put the drawers back in loaded the fridge and sat back and said I just saved myself about $200.00. You guys are awesome we got the part 2 days after we ordered it Thank you for the great service.

Tony The Birdman

First I took everything out of the fresh food door, then I removed the top hinge cover using a philips head screwdriver, and a nutdriver for the two screws holding the upper hinge. Lifted the door off the bottom pin, and placed it on the floor. Then took off the bottom hinge and used the Dremel tool to grind off the rivet holding the broken door cam on the bottom hinge. Used a nut and bolt to hold the new cam in place, and put the lower hinge back on. Then replaced the other cam on the bottom of the door itself, using the nutdriver. (Be sure to buy two cams, and have the bolt and nut to replace the rivet). Reinstalled the bottom hinge, put the door on, replaced the top hinge, and presto! Works great! Thanks to the others on this site for their stories - really helped make it an easy and quick repair!

Installation could not have been easier!

replaced lights in refrigirator and freezer

unscrewed 2 screws per rail, replaced with new rails with 2 screws each - couldn't have been easier

Pulled out the shelves, unscrewed the old rail and removed it. Two screws put the new rail on, and then I put the shelves back in. It was so simple, and inexpensive too. This is a great service you provide. Thanks!!

I looked up the brand (Kenmore) and found that there are replacement parts for the drawer rails. I put up with this problem for three years not knowing this could be repaired. I unscrewed the broken left rail and replaced with the new one. I bought a right side rail just in case all the stress of the other side being broken would cause the right side to give up too. So far so good but I will keep the new right rail for a future date. It was so easy to repair and I wasted all those years putting up with the hassel.

I loosened the compression nut on the valve with my fingers and pulled the water line free from the valve. On the other end, I just pulled it from the hose clamp. Installation in reverse. Force the water line into the fitting on top, Slide the old nut over the line on the bottom. Screw the nut onto the valve. Reach inside the freezer and turn on the ice maker. Done. Before replacing the cardboard grill, you should vacuum the coils on the bottom, front and back. If practical, push it outside and blow it out with an air compressor or a leaf blower.

First I removed the electrical plug from the back of the freezer that plugs into the icemaker. I then removed the two hex head screws that hold the icemaker to the wall of the freezer and removed the icemaker. I removed the plastic cover, which incidentally protects the gears, by prying it off with a srewdriver. I removed three small nuts(7mm) which holds the internal cam in place. I removed the cam by pulling it off the shaft. Once I got the part from you folks I reversed the procedure that I just mentioned, and put the icemaker back together. It works great. The part with shipping was around $16.00. A new icemaker was roughly $159.00. If I would have called a technician it would have cost around $300.00 to repair.

Ordered at PartSelect and received the auger and blade within days. Printed the parts diagram and proceeded to take the auger apart the time it took would have been much less but I seized the opportunity to do a deep cleaning of the old parts before replacing them....The part diagram was the key to simplicity and the fast shipping was awesome. Thanks I'll be back....

I had made a dry run at the repair after watching the instructional film provided by part select and it seemed easy enough.
The only problem was that i needed to use the electrical cord extender (provided) to adapt to my plug type. That presented a problm because it needed to be tucked up out of the way to allow the ice bin to clear. Just needed to be creative in how you wrapped the cord behind the ice maker unit before snugging the attachment screws.
Cranking out ice like crazy.

remove the 8 screws 2 for each rail
installed the new rails
slid in the meat drawer and glass
slid in the vegetable drawer and glass
presto - like new fridge !

First I removed the top hinge of the refrigerator door and then lifted it off the bottom assembly. I had to turn the door on its side to work on the bottom where the broken part was located. I unscrewed the bottom assembly and replaced the broken part with the new door cam. Put it all back together and now the door closes but must be manually pushed to close. When the door was working properly it would shut automatically when released from any position. I think I need to install an additional part - maybe a shim? to make it close automatically. That will be another story.
This was a fairly simple jog to do but since I did not have the proper tools it did take me longer than usual to remove the bolts. I'm happy I did it myself and saved a big repair bill! Thanks to the people at PartSelect.com.

I was set to buy a new magnetic seal to hold the door closed, when I looked it up on PartSelect I saw the recommendation that the problem might be the door closing cam.. I check it with a mirror and sure enough the cam had broken and the door sagged about 1/4 inch. I then followed the instruction and removed the top hinge, lifted the door off and replaced the cam. I did need two and the one attached to the lower hinge had to be drilled out and a new screw and nut attached to hold the cam. It was simple to do, I would recommend selling the door closing cam be sold in pairs with a #10 1/2 inch long screw with lock nut.

My husband took out the old icemaker in about 5 minutes. The new icemaker was a perfect fit even though the refrigerator was >10yrs old. The only difficult part was the plug extension that was needed so that it would fit into an older appliance. The part was included, it just made the cord about 3 inches longer than it needed to. After working with it for about 20 minutes we were able to fit it on the back side of the icemaker. Now it works great!!