10653569200 Kenmore Refrigerator - Instructions

I removed the glides under the edges of the meat pan, remove the old pan, put the new pan in and replaced the glides. I was very pleased with PartSelect. I ordered my part, and it arrived the very next day. I will definitely order my next replacement part thru PartSelect.

Mine is a simple tale of the missing ice cube dispensor guide. When we moved, the guide was missing so when I built our new home with a kitchen in the basement I wanted to hook up the ice dispensor but when I did, the ice cubes always fell off to one side. I decided to order the misssing part on-line. I ordered it paid for it and then received it the next day-wonderful. Within ten minutes, I was ready to go. Thanks for great service. Rick Davis, Bloomington, IL.

I installed the new cap on a new filter, which I will install when the old filter needs replacing. No tools required, but it is sometimes difficult to turn the filter cc wise, when replacing.

removed screws that held the ice maker in place, then removed the cover (popped off) The drive element was easy to remove, three screws and it was out. I put in the new part and reinstalled the icemaker with the three screws that hold it in place. I never call Sears for any repair. They use contract help and I have heard horror stories about those guys!

This was a pretty easy repair...I removed the retaining screws and slid the assembly off its tracks. Disconneting the wiring hardness was a pain but after a few minutes I had that off (use gloves, it gets cold in the freezer after a minute)

Once I had the unit completely out of the freezer the replacement part took only minutes to replace.

Reversed the process putting the ice maker back in - a few hours later my ice buck was full again.

Simple repair - well worth the effort.

Turn off water supply too ice maker and unplug the fridge power. using a nut driver remove one bottom screw from the bottom, near the front. The other two from the side atop the ice mold. (loosen screws and ice maker will lift up and off.)
I set the ice maker on the counter, snapped of the front cover by hand. using a phillips driver, remove two screws near the bottom corners.(they go through the circuit board into the ice mold)
circuit board in one hand, other end of ice mold in the other, slowly pull apart about 1 inch. remove the silver colored "on, off" bar at the end by snapping the retainer out of the ice mold. (the silver bar stays with the circuit board end)
Watch how the ice guide(white fingers stationary on side of ice mold) hooks too the ice mold on each end. swap ice guide to new ice mold, insert three guide pins on end into holes on the circuit board, while holding ice guide onto ice mold, watch rotation bar while inserting into motor.(it only splines one way.) when each piece is lined up, simply push together and reinstall two screws. snap circuit board cover into place. reinstall ice maker into freezer in reverse order.

After unplugging the appliance I removed acess cover on back of fridge with a screwdriver, pulled the overload start device straight off the compressor, unplugged the red/ white factory pre-terminated conductors and replaced the bad start device. Took about 2 minutes. You must remove as much of the dust and lint from condenser element to keep this from happening again since heat will build up and fry the overload again.

Really simple clear instructions with photos. With this the repair was quick and easy simply remove the bad relay and replace with the correct one. Great delivery time with terrific instructions.

First of all, you must remove two screws in the fridge compartment, and then remove the back panel in the freezer compartment which snaps off easily.

Then, you must push the four clips on the back of the diffuser together from the freezer side so that it slips out the fridge side.

Make sure to remember the parts as they come out, and re-connect them as needed to complete the repair.

This repair did not fix my fridge and so I'm drinking bourbon and trying to figure out how to fix this giant Kitchenaid piece of crap that freezes my beer.

Damn.

Removed the three motor screws pulled off old motor put new motor in place replaced screws and re-installed. It was producing ice three hours later. I originally tried to obtian these parts directly from Whirlpool in which twice they shipped me the wrong parts. Finally gave up on them and entered the whilrpool part number which crossreferenced to new part number which was correct the first try. Thank you!

ridiculous how a tiny plastic broken part required a full motor assembly replacement. that being said, i went online, found this website and easily identified the part i needed to order. i was impressed when it arrived within a couple of days. removing the old motor and replacing the new was a piece of cake...and i am NOT mechanically inclined,

I watched several video's on youtube that showed me how to replace the parts. Just Google "how to fix my freezer". I figured the only problem was the freezer Thermistor so I only replaced it. The refrigerator has one to. Instantly the freezer went back to Zero degrees and the defroster works fine after melting all the ice in the bottom. Make sure the drain hole is cleared. I ordered the bi-metal thermostat just in case but I don't need it. Be sure and position the thermistor down in the freezer rail on the right side just to where you can see it in the first opening and pull it back up out of sight and tape it to the wall where it comes through from the air baffle. It's important that it's 7.8 " down from the top of the freezer. Happy now, Freezer 0, refrigerator 37. This thing use to run all the time, I'm saying electricity now.

This company is WONDERFUL! I ordered the wrong drawer the first time, but their return process was a snap and the correct drawer arrived the next day. It's great to know that there is someone out there with just about every part you'll need for about any appliance that is truly customer friendly.

I removed the cover for the lower part of the refrigerator to inspect the wiring and motor. I removed the switch and removed the wiring from it. The wiring just plugs in. When the new switch arrived, I just reinstalled it to the side of the motor and the refrigerator has been working fine ever since.

Took the old one out and put the new one in.