3639604512 Kenmore Refrigerator - Instructions

I removed the old shelf and even though the new one had a slightly different texture, it fit perfectly and the two crisper drawers slid right in.

removed old ice maker, obtained part number from it. went on line ordered new ice maker at 10:45 in the morning, at 3:00 the nexte after noon new icemaker was in hand. took about 5 minutes to install new ice maker. works perfect. would do business again with this company.

I removed the ice tub. Removed the screw on the left side that holds closed the section where the icemaker plug is connected. Disconnected the plug. Then removed the bottom right screw. I was then able to remove the Icemaker by unhooking it from the bcak freeze wall. I disconnected the icemaker from the fan gaurd. Removed the icemaker cover. unscrewed the 3 icemaker screws and opened up the chamber. removed the old Ejector Blade Drive Cam by removing the outer srew that hold the gear to the icemaker. changed the cam with the new one and reassembled everything.

Used the nutdriver to loosen two screws, life out ice maker, disconnect electric plug and put aside. Placed the new icemaker on the loosened screws, plugged in electric connector and tightened screws. Used small level to verify that unit was level.Waited about two hours for first cubes to be released into tray - has been working fine since!

I removed the lower screw (not needed for the new icemaker), loosened the 2 top screws, unplugged the wire harness and removed the old icemaker. Unpacked the new icemaker assembly from the box, wiped the ice cube depressions to remove any debris, snapped on the water tube adapter, hung the new assembly on the 2 loosened upper screws and tightened the screws. The wire harness required the supplied pigtail plug which made the wire assembly long and awkward to replace the ice bucket/dispenser assembly, plugged it in and was done. It took a total of about 10 minutes for the entire operation and had a full bin of ice cubes within 36 hours and was ready for the ice dispenser/crusher in the freezer door. Easy install!

The parts were here the next day. After removing the old ice maker it was a simple installation using the adapter cord furnished. It took about 15 minutes. You have to work with the cord some to get it to fit behind the ice maker, but it does fit. The ice maker started up immediately & works great.

The repair was very simple, all I had to do is take the old broken one out and replace it with the the New Perfect Fit Part. Thank you for the great customer service ane easy ordering process.

I pulled out the old one and slid in the new one. Doesn't get any easier, but I have learned for future reference that beer in the crisper equals cracked vegetable pan.

Simply removed all items on lower shelf then removed the old dried up lime that was used to prop the broken pan before. By the way it was placed there about 3 years ago.Anyhow tossed the lime cleaned the area and easily installed the new pan cover , Thank you Part Select .com i definetly will use u all again. Until the next broken part .

Loosened 2 screws unplugged cable. Plugged in cable adapter on new unit. Plugged in to receptical, hung on 2 screws, tightened 2 screws. Done

It was as easy as removing the broken piece and replacing it with the new one. No tools required.

Removed old shelf & put in new one.
It fit perfectly and looks nicer than the
original one. Also seems like it will be
easier to keep clean.

Removed all of the stuff on the shelf, then I removed the two vegetable drawers, then I removed the cracked shelf and installed the new.

I ordered the replacement from you guys, got the new ice maker and the plug had an adapter, but it wouldnt fit in with everything. So I cut the plug off my old ice maker and put it on the new one and it works just fine.
thanks for everthing P.S. i got the ice maker from you for 109.00 and sears wanted 130.00 for it
good stuff good deal.

Set it, and forget it. That easy.