36359527994 Kenmore Refrigerator - Instructions

I ordered the wrong part, the ice maker assembly, because your diagram was not marked properly. I returned the part and you credited my account. Thanks. Ordered the new bucket. It worked fine. Now I have ice and crushed Ice whenever I want. Thanks.

p.s. I didnt use any tools, but to satisfy you I select nut driver.

All i had to do was pop off the front trim, remove 4 small screws, unplug two plugs and replace the board.

It took me a grand total of 9 minutes to get the job done.

Way cheaper than having a repair man come to the house twice, once to diagnose, and once to replace the board he would have ordered and marked up.

Remove three screws insert part; manually checked out drive and waited for ice to buildup and it worked like new.

Easy repair. Snapped cover off control panel. Removed 4 phillips head screws on control board assembly. Removed (2) connectors from assembly and pulled out defective unit. Installed new control board in reverse order. Everything now working. Very fast and easy repair once you have the part.

Found broken pieces of deflector in delivered ice. Removed dispenser, carefully disassembled it, marking fasteners, sprimgs, and levers. Local repaimen say no replacement part available, must replace entire ice maker @ $350. Found exact part in your online reference, ordered at price of $3.76, part arrived two days later--perfect fit, exactly same as original. Reassembled, and it works exactly like new. Family very happy. Good job!!!!!

First I propped up the door. Then I removed the 2 screws that hold the hinge on. AT this point you do need someone else because the door swings loose. I attached the new bracket and lowered the door. It went verey smooth. I ordered the new bracket after reading the installation stories from others who just repaced the plastic pieces. Its worth the extra money to just put on a new bracket

Was concerned that new icemaker was quite a bit different than the one we were replacing. Called GE to confirm it was correct.

Went ahead and installed the unit, using the supplied electric cable adapter.

A little difficult to deal with the extra cable, but everything worked OK and it's making ice normally.

I just slide the new one in place, using exsisting sliders. I had to remove the old grab handle from old pan and snap it into place on new pan.

I removed the 4 screws from the cover and replaced the auger and ice bucket assembly. Extremely simple and I was amazed how easy it was.

SUPER easy repair, taking about 5 minutes. After taking out the ice bin, I removed one small phillip's head screw, put the light shield in place, and tightened the screw.

Removed the face plate (4 screws) on the ice bucket/auger and put it on the new unit.

I removed all of the items in the refrigerator door. I then removed the top hinge cover with a Philips screwdriver, and removed the two machine screws holding the top hinge using a socket wrench. This allowed me to lift the door off the bottom hinge pins and set the door on its side. I removed the two screws holding on the broken bottom hinge cam riser block and replace it with the new one. After tighening it back with a socket wrench, I tried to put the door back in place. I asked my wife to hold the door steady while I lay on the floor to guide the door downward over the bottom hinge pin. I then replaced the top hinge screws and checked the door. It still didn't close on its own! I realized I had to loosen the top hinge screws and adjust the door so that it stands more vertically (evening the gap with the freezer door). With this adjustment, the door closes fine.

Very simple repair:
A. Turned off power and disconnected main copper water line into fridge.
1. Removed rear "dust cover".
2. Removed screw (with nut head) that holds water valve assembly on.
3. Removed water valve assy from fridge by lifting up - note that tab has to come out of hole in fridge.
4. Unhooked water lines and electrical connector from valve.
5. Removed 2 screws holding water valve to water valve assembly.
6. Replaced cracked water valve with new water valve.
7. Reversed process and assembled back together.
8. 30 - 40 minutes estimated time.

rerfrigator side not cooling After determinating that the defrost timer was running I turned it to defrost and watched tosee if frost started to melt. When it didn't I checked the heater with ohmeter, checked OK, so the only other component in the defrost system is the thermostat. Then just a matter of cutting and splicing wires and snapping the new thermost in place

- Disconnect the valve assembly and remove electrical connection to water dispenser valve to prevent accidental water discharge

- Disconnect tubing from valve assembly, remove and keep compression nut.

-Disconnect tubing from junction to door tube remove and keep compression nut

-Remove screws used to mount reservoir, pull tubing into main refrigerator compartment and remove old reservoir and tubing.

- Note that one of the tubes on the new reservoir is 2' too short.

- Go to hardware store to purchase 5/16" universal tubing compression junction.

- Install reservoir and feed tubing through holes in main refrigerator compartment.

- Route tubing through woven tubing protectors and clips.

- Trim tubing to length and install in valve using old compression nut.

- Splice the piece of tubing trimmed from supply side of reservoir to the outlet side tube using the fitting purchased from the hardware store.

- Connect end of tubing to existing junction using old compression nut.

- Re-connect wires to valve solonoid and test for leaks.

- Re-install valve assembly to refrigerator frame.