36368592896 Kenmore Refrigerator - Instructions

Lift the shelf off. Remove the broken pin from the slot in the door. Remove the broken end cap from the shelf - slides out with relative ease by just prying up slightly the rolled edge of the shelf where it snaps in. Slide in the new end cap. Put the shelf back in place. Literally took about 3 minutes.

I ordered the part, within two days we had received it. My husband put the part in and I really don't know what he used doing so. All I know is that the light works now and we don't have to use the flashlight. Thanks a lot.

Unplugged the refrigerator then used the cordless drill to remove the 6 screws on the access panel on the back of the fridge to be able to get to the fan. Was able to pull the fan off by hand and push the new fan on by hand. Plugged the refrigerator by in and watched the fan run for a few minutes then replaced the access panel. Really quick and easy repair.

I followed the directions on the site for the center slide replacement. I had actually called a local store and had him order the first part. It took several days and then I started searching online and found this site.Then I ordered the second part on line and to my surprise it arrived the next day. I was fortunate enough to have lived only about 70 miles from the distributer.Following the directions I found here is how I attempted the initial repair. With the vegetable bins out fo the bottom, I removed the plate covering the front frame by gently prying it off. Then I removed the two screws to losen the bar and lifted out the glass shelf. I didn't have much difficulty removing the frame since the front piece support for the slide rail that fit into the frame was already broken. I also had to loosen the screws on the back rail. I removed the entire frame and then replaced the side rail reinserting it into the end caps. I replaced the back screws and then the front ones .I replaced the glass shelf and then the cover cap for the shelf.
The only problem I encountered was that I couldn't seem to get the back screws really tight and I don't know why.

Separately (from a different site) purchased new compressor fan and motor. I purchased the grommets here because the other site listed the grommets as temporarily out of stock. I did watch one of the videos on PartSelect about the grommet replacement. Repair was pretty simple, biggest challenge was getting to the screw on the far side of the motor. Removed the two screws holding the fan motor into place. Removed motor and blade. Reinstalled with new fan blade, new grommet and new motor.

I didn’t do the repair because I ordered two grommets. When they arrived, one of the packages was empty! Instead of just sending me another one, they refunded the part so I still need one. By the way, I was not refunded half the shipping either which was more than the part itself.

Easy

On the internet forum I read that if the control board needs to be changed , do the same for the Run Capacitor/relay.
The Ge profile refrigerator was 15 years old. First I disconnect the power cord,
I removed the control board at the back of the fridge, replaced it with a new one and did the same for the run capacitor.
Plugged the power cord back and it works fine. GE repair service did not want to come to do it. DIY is fine.

Replace end cap to bottom shelf and then to door.

It was way to ez to install only a couple of minutes that's it

Removed the broken fan blade (just pulled off) and replaced with part purchased PartSelect. Very easy repair, no tools required.

I had one of my guy friends do it for me. It took him less than 10 minutes, and probably would have been quicker if he had a better screw driver. Mine is a cheap girly one that he could not get a good grip on.

The bottom shelf of my Mom's fridge broke. I found the part I needed and went to repair it. Realized both sides were broken. Ordered other side as well. Two screws in front, two screws in back. Front side had a metal strip covering screws. Had to pull that off to get to screws. Snapped back on after repair.
Mother was very pleased.
Told her to be careful. Those little pieces of plastic can be expensive.

I removed what was left of the broken endcap and slid the new one on the end of the shelf and back into the retaining slots. No tools, screws or adhesives were required.

Works like new.

After removing the food items, I removed the shelves and separated the existing broken brackets from the still good parts. I then screwed together the old working parts and the new replacement parts, all within about 10 minutes. I then placed the shelves back in the fridge and restored the food. The most time was taken picking from the food because I was hungry, but the repair itself was simple.