10648562893 Kenmore Refrigerator - Instructions

Removed back cover, noticed the start relay was a Klixon figured it was bad(they don't make a good relay);
Checked voltage going to compressor: 115V;
Checked ohms: C-S-R 4.3-4.2-4.5;
Checked ground: open;

Replaced start relay.
Compressor fired right up when plugged in.

Took off refrigerator door from top hinge and lifted off. A little difficulty getting worn out parts off (needed dremel to drill out worn plastic); replaced with new parts, the screw head holding on the part was starting to be worn as well but still worked. If I hadn't got to this repair soon the bottom of the door aluminum would have total worn out as it is, it has a deep groove but not noticeable. The new cams also force the door closed tight instead of slightly ajar at times.

Disconnect the power, removed the back panel, plastic cover and the relays. Replaced new parts, reattached the back panel and reconnected the power. The hardest part was to remove the plastic cover, it was locked on so tight,I had to use a putty knife to separate the cover from the compressor.

When I took the pan out of the box, it was not the exact same as the one I had. But it fit perfect. The only hard part was the fact that it looked so good I had to clean the entire fridge side. (Smile)

I took off the front cover with the controls. Pulled out the control knobs, unbolted the assembly (which was identical to my replacement part) and proceded to follow the old thermostat tube to the back of the fridge. The tube should be carefully removed, not pulled on, there's a couple of screws holding it in towards the back. I installed the new part in reverse of how I took out the original part. I'm very happy with how the fridge has come back to life! It was much cheaper to fix it than to replace.

Very easy. Take panel off and replace motor.. All wires matched fine. Easiest applance repair I've done..

Unplugged the refrigerator and then removed the knobs and face plate inside, by removing the screws. I then removed the screws holding the thermostat and unplugged the Thermostat assembly, and replaced it with the new one, then removed the defrost timer and replaced with the new one. I then replaced the screws and the face plate, then the knobs. I plugged the refrigerator and it kicked on right away. Within a half hour we had it running and at the right temperature. It was so easy I think my wife could have done it!

The on-line video and the hard-copy instructions with the replacement part made it very easy. Just loosened the 2 upper screws and took out the bottom one. Eased the ice maker out a bit and disconnected the plug at the back (power was off). Checked the replacement part had exactly the same wiring harness - it did. Fitted the bail arm from the old one. So simply did the same process in reverse. So 15-20 minutes after I started, the job was compelete. It takes a while for ice to start coming, but it did, and after 24 hours I threw out the ice and started again to make sure the ice came from fresh water.

Removed back panel and removed the motor put new quick disconnect on and tapped the mounting holes. Removed and cleaned fan blade from old motor and put on the new motor. Mounted motor plugged it in and replaced panel.

Removed the back panel on the refrigerator--unplugged the condenser fan motor--removed the motor--placed a small fan to cool the condenser--called parts select--ordered the motor--the motor arrived less than 24 hours after I ordered it--replaced the motor and rear panel on the refrigerator--probably saved more than $200. 00--Very happy with parts select service--plus I had a misunderstanding with my credit card and john at parts select was very helpful --not their fault--excellent company

It was so easy!

Thanks for the rush to my home on the part.

I just unscrewed the plate that locks in the light switch (screwdriver) and unplugged the old faulty part and plugged in the new switch, screwed the cover back on and I was done!

Easy!

And I am not Mr. Fix-it!

disconect the power removed the screws with the phillips screwdriver removed the front cover and then removed the rest of the screws. removed the three covers and then removed the thermostat. replaced in reverse order.

Take off back lower fridge cover. Removed old startup device. Installed new 2 piece device. Done

Found the housing for the thermostat; took housing apart pulled out thermostat and took off the hose put the hose on the new thermostat installed new thermostat and replaced housing.

replaced