36368167893 Kenmore Refrigerator - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- paul from east hanover, NJ
- Parts Used:
- WR23X10725
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Screw drivers
refig light did not work
per your instructions
Was this instruction helpful to you?
Thank you for voting!
broken slide rail replaced both sides
took out two screws both sides useing philips head screw driver put back same way
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Robert L. from Eldred, PA
- Parts Used:
- WR60X114
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Noisy fan
Emptied freezes, turned off power, took floor of freezer out [4 screws ], took two screws out of fan mounts and replaces fan. Reassembled by reverse process. Simple
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Cynthia from Seatac, WA
- Parts Used:
- WR23X10725
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
switch wouldn't come out anymore and turn light on
Gently pry out switch in door jam with screwdriver and pull both connectors off and put connectors on new switch then push switch back into the hole. Looked it up on the internet and video showed how to and also had link to new part, ordered and less than a week later the fridge is bright again. I have an older freezer also and it seems that they all use the same switches. Very Very easy
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Daniel from Orcas, WA
- Parts Used:
- WR24X446
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers, Wrench set
Refrigerator door gasket was coming apart.
I watched the video, supplied on the website, two times and followed the procedure. The repair was very easy and a pleasant experience. Lay the new gasket out flat for a couple of days in the sun prior to installation and remove the door and lay it flat for the installation of the gasket. Remove old gasket and clean track and surrounding area thoroughly. Line up new gasket over track and at each corner and press into track, starting in center of one side, and work your way to each corner - repeat on each of the remaining three sides. Use a wet sponge to slide along the top of gasket while pressing same into track on the door.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Andres from Macungie, PA
- Parts Used:
- WR24X446
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers, Wrench set
gasket cracking at least 8 years old
Excellent instructions from your video. Replaced gasket once without removing door quite harder to do. Placed gasket in sun to warm it up, didn't have to heat it in hot water. Much easier once doors are removed and replaced gasket on large table or bench. Thanks for the video and your prompt delivery of part.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Kent from Summerville, SC
- Parts Used:
- WR24X446
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver
Fresh door gasket leaking.
Followed the PartsSelect how-to video to the letter., using clothes dryer option to soften the gasket before installation. Installing the new gasket a little tedious, but not difficult. Video was dead on as to method and tools.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Gery from Tavares, FL
- Parts Used:
- WR2X7975
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Bar end cap broke
Just snapped in.
Was this instruction helpful to you?
Thank you for voting!