36358775890 Kenmore Refrigerator - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Barbara from Frankfort, KY
- Parts Used:
- WR17X4358
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Pliers
replaced water tank, to the water dispencer
son did the work BUT ONLY AFTER- trying to order the part from Sears parts online, in which they never from the right part and i spent 1 and 1/2 hours on chat and finally gave up. THEN i called sears replair, made appointment for two weeks later requesting 1st repair time of the day, was asured the repair would take place between 8-12 and beacuse it was 2 weeks away it should be the 1st repair. The day of the appt I received a phone call at 11:38 saying they would be here about 12:20, I SAID NO THANK YOU< OUR AGREEMENT WAS BY 12:00. THen I got online typrd in water tank your company come up, showed photo, and price which i ordered it can in my son fixed it and all was complete within an hr.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jabe from Little Torch Key, FL
- Parts Used:
- WR17X11653
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
In-Door Dispenser Didn't Work And Leaked Water
1. Use skewer to press plastic tabs under control panel, 2. Remove control panel and unplug solenoid, 3. Unscrew dispenser assembly and solenoid screws, 4. Press in tabs on lamp and remove assembly - unplug, 5. Replace lamp assembly, 6. Replace solenoid assembly and fasten screws, 7. Replace flapper. 8. Replace other parts in reverse order.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Carl from Denver, CO
- Parts Used:
- WR30X10093
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver
Needed new ice maker
Video is a great but still need to read the instuctions because there are parts you may need on the old ice maker. Saved myself a bit of money by not having to call a repairman. The process was very simple. I am glad I did it myself. Thank you Parts Select!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- JACOB from COLLEGEVILLE, PA
- Parts Used:
- WR62X23154
- Difficulty Level:
- Very Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver
Only crushed ice. No cubed.
Found a step by step video on YouTube made replacement very easy. Cubed ice is back. Time for a cocktail to celebrate!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Phil from MADISON, WI
- Parts Used:
- WR30X256
- Difficulty Level:
- Very Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Broken plastic on ice hopper that helped stabilize the auger
Emptied hopper
Removed screws to remove auger from existing
This was so easy I impressed my wife
Removed screws to remove auger from existing
This was so easy I impressed my wife
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Ken from Wesley Chapel, FL
- Parts Used:
- WR17X11653
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
froze in freezer
unclipped and replace with new part.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- GARY from LIVONIA, MI
- Parts Used:
- WR17X11653
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Ice Maker Clogging up from frost build-up
Turn off power
Remove operator faceplate by pullling out on outer lower corners
Disconnect wire connectors from circuit board
Remove four screws from dispenser and pull out dispenser assy
Replcae Door ASsembly
Put everything back in place
Power up
Job Done
Remove operator faceplate by pullling out on outer lower corners
Disconnect wire connectors from circuit board
Remove four screws from dispenser and pull out dispenser assy
Replcae Door ASsembly
Put everything back in place
Power up
Job Done
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- joselito from riverview, FL
- Parts Used:
- WR17X11653
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Ice Building Up In The Ice Dispenser Chute
Under the control panel there are three small holes. Insert ballpen or small flat screw driver on both outer holes to push a tab lock that holds the control panel in place. Then pull out control panel and three set of wires will be exposed and disconnect wire connectors (connectors have different sizes so you wont get confused in reconnecting). Unscrew four screws on each corner that holds the ice dispenser assembly (a part where you push your glass against to dispense ice or water. The flapper is exposed and easy to replace.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- George from Cun City Center, FL
- Parts Used:
- WR17X3909
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
The shield light had burned the shield
I hung the new shield on the two inside pegs that were already there.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Louis from LEAGUE CITY, TX
- Parts Used:
- 40A15
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver
Change bulb
Easy
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- salomon from dallas, TX
- Parts Used:
- WR17X11653
- Difficulty Level:
- Very Difficult
- Total Repair Time:
- 1- 2 hours
- Tools:
- Pliers
flapper gaskeet dried out
The video to replace the flapper looks easy, howerer the first step is to remove thestic cover of the icemaker. In my refrigerator model (as oposed to teh one shown n teh video) teh coved if firmly attached and goes under the refrigerator external plate so I was never abel to take it oot (so step 1 failed).
I was able to replace the flapper TROUGH the whole whre te ice comes from! this took lots of patients and someone with small hands!
I was able to replace the flapper TROUGH the whole whre te ice comes from! this took lots of patients and someone with small hands!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Robert from new city, NY
- Parts Used:
- WR30X10093
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
ICE MAKER gave out after 20 years
TURN WATER OFF TO REFRIDGE. TURN OFF ELECTRICITY.
Remove old ice maker (AFTER REMOVING THE BIG ICE TRAY) by disengaging two philips head screws but don't totally unscrew them. You must then totaly unscrew the bottom screw below the top two screws. Unplug the 5 head connection. (electricity)
Use adapter for the electrcity, etc from the box, (five head connection) Use the old plastic hose to hit the new cup. TIGHTEN TOP SREWS. LEVEL BY EYE. Turn the system on. Prime with some fresh water.
PS make sure that the light is on (green) and you will be in ice city. Be careful not to disengage the elcectic head when replacing the big ice tray.
HAVE A COCKTAIL!
Remove old ice maker (AFTER REMOVING THE BIG ICE TRAY) by disengaging two philips head screws but don't totally unscrew them. You must then totaly unscrew the bottom screw below the top two screws. Unplug the 5 head connection. (electricity)
Use adapter for the electrcity, etc from the box, (five head connection) Use the old plastic hose to hit the new cup. TIGHTEN TOP SREWS. LEVEL BY EYE. Turn the system on. Prime with some fresh water.
PS make sure that the light is on (green) and you will be in ice city. Be careful not to disengage the elcectic head when replacing the big ice tray.
HAVE A COCKTAIL!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Chris from Ulysses, KS
- Parts Used:
- WR30X10093
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Old Ice quit working, would make ice but wouldn't flip ice.
Removed old Ice maker and replaced with new Ice maker.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Judy from Naples, FL
- Parts Used:
- WR17X4312
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Ice Bucket got a hole in it and Auger would not work
Removed the 4 screws off the old bucket cover and place the cover on new bucket. Just that simply. Can't beat the price!!!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Robert from North Topsail Beach, NC
- Parts Used:
- WR17X11653
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Ice dispenser chute icing up
Replaced dispenser flapper
Was this instruction helpful to you?
Thank you for voting!