59657585790 Kenmore Refrigerator - Instructions

Used a screw driver to pull old switch. Pulled one wire at a time, only two wires. After wires instlled to new switch push new one back in place where the old one was.

remove front grill. with pry bar and wooden block, elevate side with broken wheel and insert wooden block behind assemble from the exterior bottom. With roller wheel assemble lose from the wooden block remove front elevator screw from the front frame. next remove cotter pin with the pliers and pull assemble pin. next elevate assemble out. drill out axle on the crimp side insert from the hardware store one 5/16 x 21/2 bolt with nut and new wheel. reinsert assemble in the reverse order. Remove wooden block and adjust height of wheel. replace grill. job complete. good job

Well folks I put up with an ice burg all summer when I really should have took the time to fix it. You know how it goes though. You get so busy you just put it off.
Well don't put this one off because this is just how easy it went.
I came home one evening and wanted to make a drink to relax but that big glob of ice was there waiting for me. I took a crewdriver and beat it down so I could pull the catch basin out. Having looked it over for a minute I grabed a nut driver and took three of the screws out that held it in. I unpluged the wire and bingo it was out. Maybe five min. had elasped.
After taking the unit out I notice how the non stick surface was coming off of the tray and that explains the black pieces that were getting into my ice.
Getting the model number off the back of the fridge and writing it down I went to my trusty lap top and did a quick search for a ice maker for my Jenn Air refrigeraton and blamo...! Part Select came up and I put the part number in their search engine and bingo again there it was, my part.
One quick order and in three days it was right there by my door when I got home.
Now i'm so excited. I went into the house and didn't even chage out of my dress clothes. Within five minutes it was in. Now I just had to wait for the timer to do it's thing and sure enough, I awoke the next morning to a whole tray of beautiful ice cubes. Wow no more ice burgs.
The moral of my story is I spent so much time hacking out that glob of ice and for fifteen minutes of my time, I could have been siping on cold ones by the pool but now old man winter is pressing down on me and I guess a lesson learned was a lesson earned. Fix it!

1 screw remove assembly. Unplug cable harness and remove old cover and wire arm. Replace cover and wire arm and attach wire harness on assembly end. Re attach using screw removed in first step. Plug in wire harness. Making ice within 30 minutes.

change light bulbs

Removed the two screws that hold flaping door. Removed the single screw that covers the connecting wires. Disconnected the wiring plug. I wiggled out the ice maker. Took off the motor cover. Swapped out one motor for the other. Reinstalled the icemaker in the resverse order of removal. Note the wiring plug in the freeze is very from. It makine s the reconnection differcult.

removed the back panel inside the freezer (several small screws) with a nutdriver. used a hair dryer to melt the built up ice. replaced the thermostat and replaced the panel. very simple repair.

Unplugged the refrigerator. Removed the screws from the access panel. Replaced the bad motor with the new motor. Works great . Probably saved myself $125.00 in a repair service call.

The web site and customer service from Partselect.com was outstanding. I had the part in two days. Their tracking system is wonderful.
First class company.......It's plain to see they put the customer first.

Repair Refrigerator Kick Plate Grill:
No tools were required. I removed old grill with hands. I attached two clips to new grill, and re-installed the new grill. (less than 5 minutes very easy)

Repair Crushed Ice Bucket:
You will need sockets or nut driver. Remove the Ice crusher dispenser and metal rod from the existing unit. You will then re-install with the new Ice Bucket. There were two scews that held the front cover. You will need to remove four screws to remove the ice crusher mechanism and re-install with new bucket. (10 minutes to replace)

Repair Ice Maker Assembly:
I removed the plastic cap on the top left edged of the ice maker. You will need to use your existing cap with the replacement unit. I then loosened the top two screws on the ice maker assembly. You do not need to remove the top two screws. There is one screw on the bottom that will need to be removed. This will allow you to get to the wiring harness. I pulled out the white tube that fills the ice maker with water. I then used a small bucket to pour existing water out of the ice maker. I used a small screw driver to depess the clip on the wiring harness. You can not pull out the wiring harnes unless the plastic clip is depressed. The new ice maker assembly did not have the same type of water line attachment. It looks like it is made for different assemblys. For my water tube, I noticed a notched area on the new unit that could be cut out to work like my existing unit did for the water line. I used a box knife to cut out the notched area. On the new water tray, there was a hole in the side that my existing unit did not have. It does not affect the installation of the water tube. I installed the new ice maker assembly by attaching the wiring harness. Installed the bottom screw using my original bracket instead of the new bracket that came with the new unit. Tightened the top screws and bottom screw. Attached the water tube to the ice maker assembly. Attached plastic cap between the refrigerator wall and left side of the ice maker assembly. (15 minutes)

replaced the bimetal defrost thermostat & defrost timer and that seem to cure the problem found repair easy and parts were here n lest than two days very satisfied with prompt sening of parts an explanation how to repair. Thank-you!!!!

I didn't know what the problem was so replaced all 3 parts.
What I think actually fixed the problem is the Cold Control Thermostat that is not listed here. This part accessed by removing the dial control in the front of the Freezer. Part wasn't exactly the same but worked. I looped the sensor toward the front of the dial. Also replaced the Run Capacitor from the the back of the unit (Very Easy). Replaced the Defrost Timer from the Front of the unit (Easy). Now keeping 35-40 degrees in the Fridge and -15-0 in the Freezer. Nice. I plan to replace the Condenser Fan Motor also as it is a bit noisy.

I have replaced the circuit board, the condenser fan motor but the unit still will not feeze correctly. The bottom of the unit freezes but just barely cools the rest of the freezer and ice box. Have you got any other advice that might help. This is a side by side unit. What else could be the problem. It seems that the fan is not working correctly or it is stuck in defrost mode. The coils where the fan is seem to be icing up but it will not let the fan work. THanks for your help, David Wilson

We have a side-by-side and the tutorial was different than what we have. Had trouble getting cover off, but finally repaired and WE HAVE ICE! Also took longer than expected.
Saved a lot!

First I removed the back cover then removed 3 nuts holding the motor. Next I removed the two wires. Next I attached new connectors to the wires and installed the new motor and everything worked perfect!

Service and shipping were fantastic! I would definitely use Partselect again!

I did a few tests with the old ice maker and determined that it was the ice maker itself that was faulty. The replacement part I ordered exceeded my expectations in the time it took to get the part. I reused the arm, wire harness and clamps from the old icemaker. Then it was a simple install into the bottom freezer compartment, turning on the water supply and bingo...lots of ice cubes.