1069334311 Kenmore Refrigerator - Instructions

Please bear in mind I am 65 years old & it was harder to get up & down off the floor then to change the switch. Was very easy - watched video, unplugged unit. I used the putty knife at the right front corner to work loose, when it came loose had to loose the left side a little. The unit pulled out easily. detached the wired that had a single plug with 2 prongs on it. Attached the plug, pushed new switch into place. There was no way you could place wires on wrong prong. When done, plugged refrigerator back in & checked if working. I CAN SEE THE LIGHT and the food in the freezer now. Thank you for making an easy repair.

I had ordered some other parts for something entirely different off your website and service was great. So after almost ten years of a dark refrigerator, because of a defective switch, I decided to see if you had the part to fix it... You did and the part got here in 3 days. I had a working light switch and all the light in the world where my husband needed it most (in the fridge). It took me at the most ten minutes to replace the part. All is well now and I have a happy husband who can find the leftovers just fine. Thanks for your great service!

Hardest part is putting in the replacement ice maker. this is easily resolved if you have a 3x5 mirror. The mirror allows you to see where the screws are and place your 1/4 inch socket. The replacement part was identical to the original so did not need to replace wiring and other items included in the package received.

After I did the prep work of removing the items inside the door the project took less than 15 minutes to get the repair job done. 1. Remove the door by taking off the top hinge cover on top of the door, remove the three screws with a socket wrench, remove the plastic gasket under the hinge, left door up and off the lower hinge pin 2. Place the new bracket on the freezer door hinge pin, flange side down 3. I had to place an extra spacer washer, which I had on hand, on top of the hinge bracket 4. Replace the door on the bottom hinge pin 5. My husband held the door in place as I reattached the top of the door with the plastic spacer and 3 screws I had removed 6. Replaced the plastic gasket and hinge cap on the top 7. With the door reattached, I removed the existing screw under the door directly below the new hinge bracket, lined up the hinge bracket to the screw hole and attached it in place. Much to my surprise and pleasure, the door swings perfectly, stopping where it should with the door shelves loaded! Thank you PartSelect for having a part that would work for my 16 year old refrigerator even though I had to add a washer shim to make the new part as thick as the original.

took out the old fill tube installed the new one and its working great. I really did not think that was going to be the problem thought it would be more than that but it was not. It took about 7min to change thanks for the fast shipping I will use you in the future.

Removed screws from the back of the part in the fridge. Pulled old part out. Measured the old part. Cut new part to fit. Replaced new part and tightened the screws. Worked perfectly.

Viewed the viedo - it showed what to do

Took socket out and replace it with new one. Very easy. W saved alot of money doing it ourself.

1)pry out the old/defective light rocker switch with a screw driver (flat head) and pull out the cables 2)unplug two connectors at the end of light rocker switch 3) connect new light rocker into two connectors 4)push the wires inside and put back new light rocker switch

I did exactly as the video showed. I popped out the old switch, disconnected the two terminals, connected the new switch and put it back. The light now works! The refrigerator is over 25 years old and the switch works! What a great website this is. Couldn't of done the job without Partselect's help.

Followed a youtube diagnostic video on a whirlpool fridge with the same configuration. After determining that the problem was the thermostat I ordered the part from parstselect. I was pleasantly surprised by both the fair shipping price and the 2 day arrival. Replacement was as simple. Cut the old wires, wire nut the new ones. Wire colors are the same on my old unit and the replacement, but these generally aren't polarized anyways.

Very easy to replace. Disconnect water line. remove 2 screws pull out filler tube. replace with new one.

hardest part was pulling out the refrigerator. it took about five minutes. parts fit perfectly. only thing to look for is some excess flashing on the end of the tube. easily removed with a pocket knife. simple repair.

Simply stick a putty knife between the switch and refrig wall. Pop out old swith, remove both wires by pulling off switch by terminals. Throw switch out. Put wires on new switch and push into slot and all done. Nothing to it! Took me 5 minutes if th

I am a landlord and while getting apartment ready for renting, I noticed the broken shelf. I got part # etc. and the shelf came in one day. I was extremely satisfied with the prompt attention that I received.