10641514101 Kenmore Refrigerator - Instructions

Removed cardboard back from refrig. Found source of smell/burn. Removed part. Ordered several replacement parts as the diagram was not clear as to which part would be needed. New parts arrived, matched with old. Cleaned carbon from contacts, installed new part. Cleaned dust from refrigeration coils, installed back. Returned unused parts.

Disconnect power to refrigerator. Removed all food from Freezer. Removed all Shelves and shelf clips. Used phillips screwdriver and removed 6 screws from lower rear panel covering evaporator coil. Removed panel. Pulled plastic fan blade off top of motor shaft. Unclip top front of black motor retainer clip which then allowed the rear clip to unhook. Removed clip. Then removed 3 wires from fan motor, noting proper location for replacement. Slide the fan motor out to the left. Installed new motor. Reinstalled clip, hooking rear side first. Then rehooked the 3 wires. Slide fan blade back on top until secure. Tested everything at this point before reassembling rear panel. Then replace rear panel, replace the 6 screws, replace shelf clips and shelves and replace food. Very easy to do and saved about $150 over a service call to troubleshoot and re-visit to install after getting part

tested thermostat and defrost time but both tested as working...called a repairman who came in and said they were both working...got annnoyed for not trusting myself. Repairman did say that he had seen defrost timers simply slow down, allwoing them to tesat as good but not actually working correctly. I ordered both the thermostat and the timer to cover all bases...actual replacement was simple.

This product comes in a bottle with a brush like Liquid Paper. It goes on incredibly easy. A second coat might be needed. I wanted to prevent rust from setting in so I covered the scratches and dings. The paint is a little brighter since my washer is 10 years old but it still looks great.

Linkage on the cold-control mechanism in the air diffuser assembly was broken. It was necessary to access the diffuser assembly from both the refrigerator and freezer sides of the unit.
Re-connected the linkage between the diffuser and cold-control assembly; remounted the two combined assemblies . . . refrigerator working nicely now.

Pulled out the old drawer and put in the new.

I was able to salvage the existing wiring and simply replace the ice maker itself and the valve located at the bottom-rear of the frig.

Simply removed and replaced the screws, changed the water tube and connected everything back up. I probably spent more time cleaning behind the frig that replacing the parts.

Very pleased with how quickly the parts came and everything was included!

I replaced the Crisper Pan with no problem. The snack Crisper Drawer doesn't come with the white trim, so you have to take it off the broken drawer and put it on the new one. I think removing the trim & putting it on the new drawer was the most difficult part since it is such a snug fit! Still, it only too a couple of minutes. Now I am wondering why I waited so long to order new drawers!! Thanks Parts Select!

Being a jet mechanic I had to familiarize myself with refrigerators, then after 2 or 4 hours of online studying, opened the door pulled the temp knobs of, removed the panel by gently prying the top of the panel out,then up and out with it. I found tapping on the thermostat shaft or wiring connection started the compressor, verifying my belief it was the thermostat. Don't mess with wiring if you don't know exactly what you are doing and unit is plugged in, you will electrocute yourself!!! I received the thermostat, UNPLUGGED THE UNIT from the house wall outlet, took one screw out of the upper inner wall at the very top to remove cover, one screw at the back top to remove the other cover (at the control vent) for access to remove sensor, then removed 4 screws , 2 front, 2 underneath to drop the housing for defrost timer, etc., and then took 2 screws from thermostat, unplugged wiring from thermostat (3 wires, be sure to put them back on the same place in the new thermostat). Remove old thermostat, slide plastic cover off sensor and slide back onto new thermostat sensor. Be careful not to kink the line or bend it to sharp you will damage it, (use gentle curves when bending it,) and re assemble everything in reverse order. This took about me 15 or 20 minutes start to finish. Plug into wall and watch thermometer to verify success.

changed the starter connected to the compressor

First I installed a defrost timer, (the old timer had burnt out contacts in it) It seemed to work for a few days, then went back to not comng out of defrost cycle, I then installed a defrost thermostat. It seems to be working better than before. I found out that maybe I wasn't running it cold enough. So I turned it up colder. Now it works ok for 2 - 3 days, then I check the Temp in the freezer and its up to 6o. So I manually reset the timer and it works for 2 - 3 days. Don't know what to do now to fix it.

I removed the screws on the upper hinge and removed the door. I removed the lower cam in about 2 minutes and had it replaced. The upper cam was a tight fit in the door and I resorted to vise-grips to remove it. Total time to replace cams and put the door back on was 30 minutes. This saved me $100.
Thanks

Water leaking from under refrigerator. Initially believed leak was from filter assembly. Removed filter and shut off water supply but leak appeared at different intervals again. Large puddle of water coming out from under refrigerator. Removed back lower panel and checked for leak, but didn't find any. My wife was also checking for leak and found a crack in drip tray. Only way we could get the drip tray out was to first remove front lower panel, disconnect and remove wiring harness in front of drip tray, unbolt water filter assembly, and unbolt water solenoid unit at rear of refrigerator. Their water lines connect to filter assembly. My wife controlled the water solenoid unit to give me play as I pulled the filter assembly out as much as I could from the front. I could now wiggle the cracked drip tray out from under the filter unit. Replaced drip tray and reinstalled wiring harness, water filter unit w/new filter, and re-bolted water solenoid unit at back of refrigerator. Replaced back lower panel after turning water back on and checking for leaks. Replaced front lower panel.

The reason still had leak after initially turning off water supply was because the drip tray is used to catch the water when refrigerator goes into the defrost cycle. Since the original drip tray had cracked, water only appeared on floor after defrost cycle.

I removed the glides under the edges of the meat pan, remove the old pan, put the new pan in and replaced the glides. I was very pleased with PartSelect. I ordered my part, and it arrived the very next day. I will definitely order my next replacement part thru PartSelect.

After unplugging the appliance I removed acess cover on back of fridge with a screwdriver, pulled the overload start device straight off the compressor, unplugged the red/ white factory pre-terminated conductors and replaced the bad start device. Took about 2 minutes. You must remove as much of the dust and lint from condenser element to keep this from happening again since heat will build up and fry the overload again.