3639537851 Kenmore Refrigerator - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Richard from Atlanta, GA
- Parts Used:
- WR17X11653
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Frost was building up inside the freezer just above the ice dispenser shute.
Followed the instructions and replaced the door recess.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Thomas from Arlington Heights, IL
- Parts Used:
- WR17X11653
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Frost on the bottom of the ice bin frome warped rubber flapper
Pulled the outter cover off, removed the electronic board, replaced the flapper and put it back together again.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jason from zion grove, PA
- Parts Used:
- WR17X11653
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
rubbeer flapper was worped causing frost in the freeze
The same as the vidio, very easy. Thank you
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- KEVIN from MITCHELL, IN
- Parts Used:
- WR30X10093
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Icemaker Wouldn't Totally Work
Loosened 2 screws unplugged cable. Plugged in cable adapter on new unit. Plugged in to receptical, hung on 2 screws, tightened 2 screws. Done
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Robin from Georgetown, TX
- Parts Used:
- WR30X10093
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Our icemaker quit working.
My husband took the old icemaker out before the new one came in. When the new one arrived, I installed it in less than 10 minutes.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- VINCENT from SPOTSYLVANIA, VA
- Parts Used:
- WR17X3489
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Tab that holds light shield was broken off.
Removed ice tray and set on kitchen counter .One small phillips scredriver to remove broken tab.
Attached replacement shield with screw, replaced ice tray. Probaly total of 5 to 10 minutes to find scredriver, do the repair & replace screwdriver where it belonged. Took more time to place order then do repair. Add a couple of minutes to unpack.and some more time to drop off cardboard box at recycle center.
Attached replacement shield with screw, replaced ice tray. Probaly total of 5 to 10 minutes to find scredriver, do the repair & replace screwdriver where it belonged. Took more time to place order then do repair. Add a couple of minutes to unpack.and some more time to drop off cardboard box at recycle center.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Craig from Hanna City, IL
- Parts Used:
- WR30X10093
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver
Ice maker would not work.
Removed the Ice maker from the freezer because the light was not on. Disassembled ice maker, found printed circuit board had shorted across two posts because the board was black in that area. Bought new ice maker assembly, installed in less than five minutes, making Ice fine.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- HERBERT from Harlingen, TX
- Parts Used:
- WR17X11653
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
gasket was shot
took off the panel, took out 4 screwws, took out old flap, installed new flap, put screws back in , and put trim back on.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Ben from Northville, NY
- Parts Used:
- WR30X10093
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver
old ice maker quit
removed old ice maker, obtained part number from it. went on line ordered new ice maker at 10:45 in the morning, at 3:00 the nexte after noon new icemaker was in hand. took about 5 minutes to install new ice maker. works perfect. would do business again with this company.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Fred from Brooklyn, NY
- Parts Used:
- WR30X10093
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver, Screw drivers
My Icemaker arm was broken. It didnt move up or down by itself.
I removed the ice tub. Removed the screw on the left side that holds closed the section where the icemaker plug is connected. Disconnected the plug. Then removed the bottom right screw. I was then able to remove the Icemaker by unhooking it from the bcak freeze wall. I disconnected the icemaker from the fan gaurd. Removed the icemaker cover. unscrewed the 3 icemaker screws and opened up the chamber. removed the old Ejector Blade Drive Cam by removing the outer srew that hold the gear to the icemaker. changed the cam with the new one and reassembled everything.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- William from Arrroyo Grande, CA
- Parts Used:
- WR30X256
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Hole in bottom of ice bucket
Transferred ice supply to another freezer. Removed ice maker unit from freezer and studied assembly. Removed the 5 screws holding the bucket in place while keeping track of which screw went where. The only positional component to remember was the motor control pivot retainer. Wiggled and fiddled to remove the old bucket. Wiggled and fiddled to put the new bucket in place. Replaced the 5 screws, dumped the reserved ice back into the bucket, and returned the ice maker unit to the freezer.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Opie from Carrollton, GA
- Parts Used:
- WR30X10093
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
replaced the ice maker
I ordered the replacement from you guys, got the new ice maker and the plug had an adapter, but it wouldnt fit in with everything. So I cut the plug off my old ice maker and put it on the new one and it works just fine.
thanks for everthing P.S. i got the ice maker from you for 109.00 and sears wanted 130.00 for it
good stuff good deal.
thanks for everthing P.S. i got the ice maker from you for 109.00 and sears wanted 130.00 for it
good stuff good deal.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Dudley from North Little Rock, AR
- Parts Used:
- WR30X10093
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Screw drivers
new part was substitute/which was some what different and was hard to get tray back in because power cord would not let it
i did every thing according to instructionwhich was simple but it did not cover how to use the extension electrical plug-in and where to put the extra cord so the tray would go back in
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Carmine from Millington, NJ
- Parts Used:
- WR17X2740
- Difficulty Level:
- Easy
- Total Repair Time:
- 1- 2 hours
- Tools:
- Pliers, Screw drivers
Replaced corroded auger
Removed front cover, removed rear cover careful to note position of spring assisted parts, used pliers to unscrew auger rod end cap, removed and soaked in Lime Away fixed and movable blades. Reassembled using diagram on website for guidance.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Nghia from San Jose, CA
- Parts Used:
- WR17X2740
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers, Socket set
Replace Rusty Item
Before disassembling the parts need to replace, I use my digital camera to get all the different angle of the item so I have the full reference to asswmble the new one
Was this instruction helpful to you?
Thank you for voting!