25368137892 Kenmore Refrigerator - Instructions

First I removed 2 screws and removed broken railing then placed new railing ad screwed in new screws then replaced drawer into railings. Thank you so much for the excellent service in geting me the correct part in a timely manner.

From most posts I've read, the defrost timer was the culprit so I blindly ordered one. Easy install but did not fix the problem so I broke out the ohm meter. The only other 2 items it could be all tested good with my meter so I bypassed the defrost thermostat (per forum help...actually quite easy)and it defrosted fine, which told me I needed a new defrost thermostat. Installed fairly easy and problem gone.

Based on the website I decided it was most probably the defrost timer, and that was correct. I ordered it, watched the video, and two days later the part was at my door. Took the nut driver, removed 4 screws, then removed the old defrost timer, installed the new one, re-installed the whole plastic assembly with the four screws, and done!!! Couldn't have been easier.

All I had to do was remove the original support that was on the inside wall of the refrigerator, which I had to use pliers since there were broken pieces, and then I just snapped the new one into the three holes provided for this support. The crisper drawer works fine now. It literally only took about 1 minute.

removed freezer door and installed the new one. This was a pretty easy thing to do, although putting the old handle on the new door was a challenge. No knowing that there is a plastic piece holding the top of the handle i broke the that piece and had to order another one. Mean while the freezer was making alot of frost inside, so that had to be cleaned after the new part came.

Placed end cap on one end of rack and attached to one side of the door by applying hand pressure.
Inserted the other end of the rack into the end cap'
and again applied hand pressure to insert into slot, Repairs completed.

Use the rubber brushing to fill the gap.

Put the end caps on the metal bar and put it on the freezer door and it snapped right in.

Very easy to do in less then 4 minutes to do both shelves.

Thank you very much.

They were the wrong parts. I read a question another person asked and it advised to order these parts. Didn't want to waste my time anymore and threw them away.

I used a flat head screwdriver to pry open the front of the socket as I pushed the socket toward the freezer side. I unplugged the two wires connected to the socket then re-connected the two wires to the new socket and popped the new socket back in. I then put a new light bulb in and we had light again in the fridge.

I unsnapped the old clips from the bar, installed one end cap to freezer door, clipped other end cap to bar, slid bar into end cap installed in door then snapped other end cap into place. Repeated for second shelf bar as those end caps were broken as well. No tools were needed.

After realizing the engineering on this dryer was different, I was able to access the temperature control thermostat through the front, along the side of the heating element. Several philips screws hold the front on, removing them allows you to take front panel off. At that point the heating element is below. I took a picture of the wires, so that when I started removing them, it would be easy to reconnect. Two screws hold the heating element in place, upon removing the heating element housing pulls gently forward and out, be careful of the wires, the thermostat is the second thing connected to the housing of the heating element. Two more philips screws hold the housing to the bottom of the dryer. Two wires are removed from thermostat, which is also held in place by two philips screws. Remove wires, one at a time and place on thermostat exactly as they were on old thermostat. Hold new thermostat in place with the two Philip screws, and reassemble in reverse order. And enjoy your working dryer once more, hopefully for years to come.

I watch the how to repair video on line and the repair went very quick and easy.It was just like the video,no hidden suprises.

The meat drawer is already pulled out because the broken rail could not support it. 1st I removed the shelf. Then I removed the 2 screws connecting the rail to the shelf. I then replaced the rail, screwed it together and put the shelf back in place. I put the meat drawer back on the rails and it's done.

I want to start by saying that I am female and want to let all females know that we can do home repairs! My story is not just about the repair but the wonderful customer service at PartsSelect.com. I have used them MANY times to order missing parts for appliances (I own rental property and tenants are always "losing" or breaking appliance parts). This particular time was the first time I received an incorrect part...not sure if it was my ordering or the wrong part was shipped. I contacted PartsSelect.com by email and got a REAL response within 24 hours. The customer service person who responded, immediately credited my account and "found" the correct part to order and less than 48 hours after my first email to them, my new part is already on it's way! I know it will only take minutes to finish my repair and am really impressed with their response time and professionalism when there is a problem. As a rental property owner, I will continue to use and recommend PartSelect.com.