1067690981 Kenmore Refrigerator - Instructions

After discovering that the water noise was coming from the rear of the refridgerator upon pulling it foward I discivered the connection line had broken. So i got a phillips screw driver and removed the the two mounting screws and saw it was one piece. I easliy found the part on PartSelect website and once I got I merely swaped them out and it works good as new!

take out Ice maker tray, remove three screws holding the ice maker, unplug electrical connector. Replace with new Ice maker,Ice started to fill the tray. ENJOY!!
THANKS.

It was not complicated but it took more squeezing and reaching into the narrow space than actually removing three screws and unplugging the electrical harness. But that was all that was necessary, to install, three screws held the unit in place and re-connect the electrical harness. It saved me about $100 in labor and the inconvenience of scheduling a service call and waiting for a week or so. The best part was that I ordered the unit on line on Tuesday eveining and it was at my home by Friday afternoon with no extra shipping charges. Great service!.

I first replaced the switch and had no results, I then ordered the Light Socket Kit, and because I had the experience of removing the panel to replace the switch, it took a few minutes to remove the two screws behind the panel, removing the temperature control knobs and then releasing the face plate which is secured by tabs at the bottom. The kit came with extra connectors in case they were needed, but they were not in my case and so I pulled off the wires, pushed the old socket out and the new one in. Attaching the wires to the correct pins, I screwed in the light bulb to be sure that the fix was correct and determining that, I replaced the screws that held the panel in place. Voila, I'm a happy camper who found some outdated jars in the back corners of the newly lighted shelves.

this is a snap! 2 screws an a nut to tighten and it works like a charm. the filler tube in my Kenmore refer had broken off in the back. ( really bad location to put this in the beginning) if you push the refer to close to the wall you can break it off easily. remove the water line by loosing the nut and remove the hose from the fill tube ( This assumes you have already turned of the water supply or you are standing in a large puddle)remove the 2 screws that hold the filler tube in place. pull out the old filler tube in and slightly upright motion. replace the new fill tube into the same hole and replace the screws. replace the hose and tighten the nut, turn the water back on and check for leaks your done !!
doesn't that feel great?

Took the old one out and plug the new one in, simply as 1 2 3. Order the part one morning,it was here the next afternoon, the ice maker was fixed in less than a half hour. we will order from you the next time.

First the small screws you sent did not fit.I had to cut and mend the old ones (2) to use them.I did purchase a connecting valve tha I used to connect the part of tubing (my name for it) from old one to new one.I was surprides it is working fine.Not bad for a nurse!

I determined that the ice cube maker was no longer heating the cubes so they could be released into the ice tray. After ordering a new unit, taking out four screws and disconnecting the quick disconnect of wires I plugged the new one in and we were back in business.

Repair went well,took about five to ten minutes to disconnect the power from the fridge removed the defective switch installed the new one ,reconnected the power,,,and Let there be light and there was light!

I took out the ice bin and in the back where the auger meets the ice bin I had to replace the small plastic piece to hold the auger in place when using the automatic ice maker. It was an easy fix.

directions very well written, easy to follow, no problems

Exactly as the demo instructed. It was very detail friendly and was very easy to follow.

I was able to transfer my old ice maker from my old Roper Refrigerator/Freezer into my new Whirlpool Sidekick Freezer. Everything transferred directly except for the water fill tube. I ordered one on line and simply cut it to the right length, removed the cover plate inside the freezer compartment and the little sticker from the outside. Inserted tube and fastened in place with two screws (not provided but was able to use the screws that were in the holes inside the freezer before the ice maker went in. Works great. By not buying the ice maker with the freezer I saved a hundred bucks or so.

1. Put pieces of wood under door to support it.
2. Unscrew three screws holding door hinge.
3. Disconnect water line.
4. Unscrew screw holding each cam. One to door and one to hinge.
5 Replace cams.
6. Retrieve plate with threaded holes behind frame that the hinge attaches to.
7. Use thin philips screwdriver through the hinge bracket, shim, frame and screw plate to align it for the other two screws.
8. Replace all three hinge screws.
9. Connect water line fitting.
10. Remove wood for door support.
11. Check door for smooth movement and strong pressure when closed.

Heated new door gasket in clothes dryer for 10 minutes. Moved all food out of door into refrigerator proper. Removed door from refrigerator and laid flat on living room carpet. Placed a tarp over the refrigerator opening. Loosened nuts on door holding gasket in place. Removed old gasket as I went. Inserted new door gasket. Needed to use putty knife to get new gasket seated properly. Re-tightened nuts as I went. Rehung door on refrigerator.