59650392000 Kenmore Refrigerator - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Sameul from Las Vegus, NV
- Parts Used:
- R0161092
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Screw drivers
Thermostat would not work
First I removed the knobs, then the plastic cover over the thermostat. Then, I removed the two screws that hold it on. I removed the thermostat, unplugged the electrical leads, and pulled out the old thermostat. I then inserted the new one, hooked up the leads and reassembled.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- kevin from cody, WY
- Parts Used:
- WP12544101, WP12544001
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Wrench (Adjustable)
Ice maker and water don't work
turned water supply off, unhooked both set of
valves, reinstalled them, tested operation.
one valve on primary had to be capped also.
valves, reinstalled them, tested operation.
one valve on primary had to be capped also.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Elaine from Milton, FL
- Parts Used:
- R0181181
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers, Socket set
Part of cam broke off bottom of fridg. door & it quit closing automatically
Took longer to move food from door to inside fridge & take grandkids' artwork off door, & then put it all back than it did to replace cam.
1. Used phillips head to undo 1 screw holding cover over top bracket; lifted off cover.
2. No need to have someone hold door while you remove top bracket; magnets in door gasket will hold it tight to fridge. Used socket to remove 3 screws in top bracket & lifted bracket up off top of door.
3. Door's not heavy. I stood on a sturdy chair to get better leverage. Opened the door enough to break the magnetic seal & llfted it up off bottom bracket. I moved it over just enough to get to the cam, rested the bottom of the door on the floor, & leaned it up against the open front of the fridge to help preserve chilled food.
4. Removed the 1 screw holding in the bad cam to the bottom bracket (uses smaller socket than screws on top bracket).
5. I checked part that goes up inside bottom of door & it was fine, so did not replace it.
6. Trickiest part: putting the door back on. I put a hand mirror on floor by the right corner & facing up so I could see the underpart of the door as I lifted it eased it down on the right place.
7. Closed door, made sure it was straight, replaced top hinge & cover, food, & artwork.
1. Used phillips head to undo 1 screw holding cover over top bracket; lifted off cover.
2. No need to have someone hold door while you remove top bracket; magnets in door gasket will hold it tight to fridge. Used socket to remove 3 screws in top bracket & lifted bracket up off top of door.
3. Door's not heavy. I stood on a sturdy chair to get better leverage. Opened the door enough to break the magnetic seal & llfted it up off bottom bracket. I moved it over just enough to get to the cam, rested the bottom of the door on the floor, & leaned it up against the open front of the fridge to help preserve chilled food.
4. Removed the 1 screw holding in the bad cam to the bottom bracket (uses smaller socket than screws on top bracket).
5. I checked part that goes up inside bottom of door & it was fine, so did not replace it.
6. Trickiest part: putting the door back on. I put a hand mirror on floor by the right corner & facing up so I could see the underpart of the door as I lifted it eased it down on the right place.
7. Closed door, made sure it was straight, replaced top hinge & cover, food, & artwork.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Tuan from Garland, TX
- Parts Used:
- R0161088
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver
water stop pumping follow by refrig stop cooling
the problem was the evaporator has frozen causing the water line to freeze also.
I opened the cover to see the evaporator, verify it was frozen, try to unplug and let it thaw, but it would freeze again. Thought the defrost thermostat was not working but did not verify, order new one and replaced; it did not work. After a long time of experimenting different things I found out that the defrost thermostat was supposed to be clamp to the line. It was not clamped to the line, was just hangin from its wires when I found it. So.....it works now!!! but I don't know what happen in the first place: the clamp fell off, or did it come from mgfr unclamped but happen to work since it was cold new, now getting old and not cold enough to close the thermostat unless on the line? anyway, it works and I decided to keep the part for spare. Hope this help someone else!
I opened the cover to see the evaporator, verify it was frozen, try to unplug and let it thaw, but it would freeze again. Thought the defrost thermostat was not working but did not verify, order new one and replaced; it did not work. After a long time of experimenting different things I found out that the defrost thermostat was supposed to be clamp to the line. It was not clamped to the line, was just hangin from its wires when I found it. So.....it works now!!! but I don't know what happen in the first place: the clamp fell off, or did it come from mgfr unclamped but happen to work since it was cold new, now getting old and not cold enough to close the thermostat unless on the line? anyway, it works and I decided to keep the part for spare. Hope this help someone else!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- bill from escondido, CA
- Parts Used:
- W11384469
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver
light inside fridge was flickering and clicking
tested bulb good ,replaced door switch first(least expensive)then ordered light socket and circuitboard.If clicking sound is heard replace circuitboard first to save on return shipping because the switch and socket where ok
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Martin from Rutherfordton, NC
- Parts Used:
- WP4373559
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
coupling on water line thru freezer door cut due to moving Refg and having to remove doors.
Snapped the large end of the coupling onto the main line coming from the water source and snapped the other end onto the small line leading to the ice maker. Quick and simple.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Kenneth from New Braunfels, TX
- Parts Used:
- WP2182124
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Ice stripper broken on ice maker
I unplugged the fridge. Loosened the 2 top screws on the ice maker and removed the lower screw. I disconnected the wiring harness and removed the Ice maker. I removed the plastic timer cover in front. I then loosened the screws on the face of the ice maker and removed the broken ice stripper and replaced it with a new one. Re-tightened the screws on the face, installed the timer cover, plugged in the wiring harness, re-attached the ice maker. Plugged the fridge back in and walla, it was making ice in 30 minutes!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Daniel from Rhinelander, WI
- Parts Used:
- D7824706Q
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver
Old Icemaker noisy and stopped making Ice
The old icemaker had a bad motor and would stall in the fill cycle causing my kitchen to flood on occasion.
The new one was so quiet, I thought it didn't work!
Anyway, one nutdriver and 5 minutes and I had the new one in there... It is so quiet, and I always have plenty of ice now!!!
Thanks!!!
The new one was so quiet, I thought it didn't work!
Anyway, one nutdriver and 5 minutes and I had the new one in there... It is so quiet, and I always have plenty of ice now!!!
Thanks!!!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- David from Cedarville, OH
- Parts Used:
- 833697
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- More than 2 hours
- Tools:
- Screw drivers, Socket set
Freezer was not staying cold enugh for ice maker to work. Discovered fan was not working to cool condensor. Fan motor would only run if manually turned.
Unplugged refrigerator. Removed lower back access panels and panel running up the back of refrigerator. Removed and disconnected old fan. Removed old fan motor from mounting bracket. Removed fan blade from old fan motor and placed on new fan motor. Connected new fan motor to power supply. Tested. Reinstalled.
Was this instruction helpful to you?
Thank you for voting!
Freezer is not constantly holding temp
Removed the back wall (several screws) of the freezer too get at the thermostat and removed the thermostat and after checking to makes sure I plugged the wires in correctly I replaced the defrost timer by removing the housing that held it in place, which was located underneath the freezer compartment on outside of the unit. That was it!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Don from Macedon, NY
- Parts Used:
- WP12544101
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver
refrigerator sedondary water valve failed
First, I didn't know that my refrigerator water system even had a secondary water valve; I have replaced the primary water valve 3 times so far, and when that didn't fix the problem I looked further and there it was.
I turned off the water supply to the refrigerator and unplugged it, prior to working on it.
Then I took the back panel off the 'frige with a cordless drill (the 1/4" hand nut drive was too slow), removed the primary water valve to get it out of the way, and remove the secondary water valve. all the electrical and tubing connections could be removed and installed by hand, so it was pretty easy.
The job duration could have been cut in half if my wife didn't make me clean behind the 'frige once I moved it....................
I turned off the water supply to the refrigerator and unplugged it, prior to working on it.
Then I took the back panel off the 'frige with a cordless drill (the 1/4" hand nut drive was too slow), removed the primary water valve to get it out of the way, and remove the secondary water valve. all the electrical and tubing connections could be removed and installed by hand, so it was pretty easy.
The job duration could have been cut in half if my wife didn't make me clean behind the 'frige once I moved it....................
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- rosemarie from duarte, CA
- Parts Used:
- WP67002052
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers
ice wheel was broken
remove the bin from the freezer, there are 2 tabs on the lower front cover that pop off and you just pull the entire front cover off. there are 4 nuts that hold the blade cover which you can use the 7in1 with the insert removed.. i believe it's 5/16". remove the cover and the tumbler assembly pops out of the tray.
remove the nut with a set of pliers and lay it out on the table in order.
install is reverse of removal. make sure you get all the washers in the correct location when assembling. don't tighten the nut too tight or it will bind the rotating assembly.
enjoy retrieving ice from the door again!
remove the nut with a set of pliers and lay it out on the table in order.
install is reverse of removal. make sure you get all the washers in the correct location when assembling. don't tighten the nut too tight or it will bind the rotating assembly.
enjoy retrieving ice from the door again!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Matthew from Aurora, CO
- Parts Used:
- WP628356
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Screw drivers
Broken cup water fill on ice maker
I called the local Amana repair man, wanted $150 for a new ice maker because they could not get the part I needed. Found Partsselect.com and the part cost $17 with shipping. They saved me over $100. The repair was very easy too, just removed a couple of screws.
Thanks,
Matt
Thanks,
Matt
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Paul from Biscoe, NC
- Parts Used:
- R0181175
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Crack in Water Reservoir Kit, causing water to leak inside the refrigerator door each time the water dispenser selector was pressed. Also ice despenser was not making much ice due to crack in reservioir .
Removed screw that held the old Water Reservoir Kit with screwdriver. Used box cutter to cut line in and line out of old reservoir kit and cut off enough of the length of line in and line out of new reservoir kit to make a good fit between old and new lines. Added the connection fittings between the old lines and new lines just below new water reservoir kit inside refrigerator door. Did not need to replace entire lines because the old water lines was in very good shape. This cut down on the repair time. Entire job took about 15 to 20 minutes. This corrected the leak and ice maker now makes plenty of ice.
Was this instruction helpful to you?
Thank you for voting!
The freezer and refrigerator stopped cooling
I unplugged the unit, removed the freezer racks and removed the back panel to expose the evaporator. I removed the defrost thermostat, unplugged the wires, and installed the new thermostat. I replaced the panel and racks then removed the defrost timer kit by removing the two screws that fastened the cover to the refrigerator and the two screws that secured the timer to the cover. The timer is centered behind the front toe grille assembly. I installed the new timer, replaced the cover, and plugged the refrigerator in. It took several minutes for the defrost timer to advance before the evaporator fan would come on.
Was this instruction helpful to you?
Thank you for voting!