1068364752 Kenmore Refrigerator - Instructions

Removed brokent tube fitting from the compression nut.
Removed two screws holding the fill tube. Removed and replaced the fill tube. Direct replacement, no cutting tube length. Reconnect water line to the new fill tube.......Done.

After first unplugging the refrigerator from it's electrical power source,I removed the lower screw of the ice making unit with a nut driver. I then loosened the upper two screws which hold the retainer clips that secure the unit tight to the freezer wall. I then lifted the unit upward and outward a few inches to allow access to the wire harness. I unplugged the haness from rear of the freezer and removed the unit completely.
To install just reverse the procedure.

Loosened two top screws using a hand held mirror and screwdriver and removed a bottom screw then unplugged the unit inside. Five minutes and repair was complete. Easy as that!

inserted a knife between the switch and the plastic interior in order to pop the switch out.
then took off the 2 wires on the old switch put them on the new switch and reinserted the switch into the plastic interior.

I removed three sheet metal screws, unsnapped the electrical pigtail. Then snapped out knock out on new maker. Matched the electrical connection, pushed it in place. Finally set new one in place, leveled it, tightened the scews and walked away.

I took a chance and ordered a switch that is next to the top of the door. looked for how to remove it easily done in ten minutes works fine last long time.

It was exactly as everyone else described--remove old ice maker, unplug, plug in new ice maker, attach new ice maker. 3 screws, 1 plug. My plug was the one on the ice maker not on the refrigerator (ie I used the wiring/plug that was already in the freezer).

removed three screws pluged it in and it was ready to go. I must add That I ordered it one day and received it the next day by fed ex. I could not believ how fast the service was also the new icemaker is working great. I will order any furture parts I need from Parts Select. Also have given your web site ot several other people. Thank you very much.

On my particular model refrigerator I only needed to remove one screw and disconnet the plug. I then slid the unit out. The new ice maker did not come with the plastic sled that was attached to the old unit. I removed and attached the sled to the new unit with 3 screws.

Ice maker wouldn't eject the ice often enough. After reading a few other stories, I just ordered the universal ice maker from Part Select. All I had to do was remove some of the plastic shrouds from my old ice maker and put them on the new one. I also reused my mounting brackets. The whole job took me 20 minutes.

Simlpy removed two screws to remove the old part. replaced the new part and put the two screws in. Job finished.

The plastic part that connects the fresh cold water to the ice maker in back of the fridge cracked.
Do to the fact that Whirlpool has the part stick out on the back top part of the fridge. So if you push the fridge just an inch too far back the plastic part will crack.
I ordered (The Part S&H)- came to about, $11.00.

1. Turned off the cold water under the sink.
2. In the back of the freezer section. I unscrewed the two screws that held the old broken part to the fridge.
3. I opened the freezer section and cleared out the top shelf till I could see the back of the fridge.
4. I removed the old plastic part by pushing & wiggling it about forward and it then extended out the back of the freezer side and then I pulled it out the back and it came out.
5. I slid the new replacement part in basically the reverse of step 4.
6. I connected the hose in the back. To the new, replacement plastic part, that fills the automatic ice tray with water.

7. Once finished I glued a small 2”x2” piece of wood next to the new part so the fridge will never get too close to the back wall so to never break that part that sticks out again.
Before just a small bump could break the part and water is everywhere and this leak could happen slowly at first and the next day what a mess.
Some fridges have this part recessed into the back of the fridge so this would never happen as my other fridge has.
Also, this might seem like more work then it was. It was very simple. I was scared I'd screw it up, but just did it step by step. If I had someone do it. It would have cost me a bundle.
It took more time to type this, then to do the work.
I had no instructions to follow, but again, was easer then I thought it would be.
I hope that this was helpful,
Jim Vourakis

i noticed that no water was getting to the ice maker. rather than messing around with parts, i bought the entire unit. easy to remove old one and install new one. thanks...ice started again in about an hour. unit cost less than a service call!

Removed the old ice maker (2 screws, about 2 minutes). Read the excellent instructions. Prepped the replacement unit by adding the mount bracket. It plugged straight into the existing fridge wiring harness. Amazing how standardized icemakers are! Total time for a very careful job was under an hour.

It came in the mail, I got home about 5pm and had it installed that evening before dinner. First load of ice was in the catcher before I went to bed.

Very nice kit, and economical compared to a new fridge!

The parts were reasonably priced, shipped promptly and received in a couple of days. I reviewed a YouTube video before starting that was beneficial. Huge savings over retail repair service. A+ replacement parts house and I would highly recommend.