25362073302 Kenmore Refrigerator - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- James from PHILADELPHIA, PA
- Parts Used:
- 5303918202
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver
Evaporator was freezing up and was running non stop
I tested the components in the refrigerator defrost function. I used digital multimeter and checked for continuity. Defrost thermostat must 32 degrees or lower.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Kasey from O'Fallon, MO
- Parts Used:
- 240338101
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
had no shelf bin
Just snapped it on.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Benton R. from Elkton, VA
- Parts Used:
- 240495804
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Hook on end of snap-on freezer bin broke.
The existing bin fell off when the hook broke as the freezer door was opened. Finding and ordering the replacement part was about as simple as it can be. Delivery time was less than a week. Replacing the bin was just a matter of snapping it in place, which took all of 5 seconds.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Harold from Grants, NM
- Parts Used:
- 215846602
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Defrost timer was not working
Found the part on this site ordered and received part in 3 days. Took approx. 10 min to replace. Thanks for the quick service.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- robert from ELKHART, IN
- Parts Used:
- 240356501
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Right side meat drawer rail cracked
1] Pulled the meat drawer out. 2] Removed the shelf holding the meat drawer. 3] Unscrewed the right side rail. 4] Installed the new rail and screwed in place. 5] Re- installed the shelf and meat drawer.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Robert from MONTGOMERY, IL
- Parts Used:
- 5303918202
- Difficulty Level:
- Very Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Socket set
Coils frozen over. Refrigerator not cooling
I cut wires from bad thermostat and removed it . Stripped wires and crimped connectors on new thermostat and wires from old thermostat. Used heat gun to seal sleeves over connectors. Very helpful video from this site Thanks, you will be my go to parts supplier from now on!!!!!!!!!!!!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Salvador from SANTA ANA, CA
- Parts Used:
- 5303918202
- Difficulty Level:
- Very Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Pliers
Freezer worked, refrigerator didn't. Ice build up on coils.
Unplugged refrigerator. Emptied freezer and removed ice maker and cover, need to unplug fan. Defrosted coils with hot water. Cut wires to thermostat as close to it ad possible to leave extra wire in case of an error. Stripped wire in new thermostat and put in shrink plastic then the wire crimp connector joining both light blue wires making sure wires were in before crimping them. Repeated with other dark blue wire. After used the heat gun to shrink the protective white tubing. The only thing i found not satisfying was tge tubing. It was too wide and too small. When i shrunk it did not cover the whole connector and was loose. I had to use a glue gun to cover both ends of each wire connector. Hope this helps other users.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Donald from Okeechobee, FL
- Parts Used:
- 5303918549
- Difficulty Level:
- Very Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver
Intermittent loud noise coming from fan motor located in freezer compartment
Ordered a new evaporator fan motor and watched the repair video supplied by part select on their web site.It was spot on step by step instructions
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- SHERRY from LAUREL, DE
- Parts Used:
- 241872512
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Socket set
No problem
It was so easy to install it. I did great!!!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Herbert from Hayes, VA
- Parts Used:
- 241872512
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Door gasket failed
Simple. Just pull old gasket free from door. Pace new gasket on door and ensure that gasket is seated in the gasket channel all the way around door. This part fit door properly.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Michael from TUCSON, AZ
- Parts Used:
- 240505801
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Light not turning on when door opened
Used a flat head screwdriver to pop out the old switch, removed the contacts and placed on the new switch, popped the switch back in. Done in about 2 minutes.
Was this instruction helpful to you?
Thank you for voting!
Meat drawer rail broken
Removed the meat drawer and shelf from refrigerator. Removed 1 screw from right side rail. Slid rail forward and removed from slot. Inserted new rail into slot, and aligned with screw hole. Installed screw. Repeated process on left side rail. Reinstalled shelf into slots and slid meat drawer into place.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Earnest from BOWDON, GA
- Parts Used:
- 241872512
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Gasket was damaged everything inside would freeze
Pulled the old gasket out and pushed the new one in.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Michael from CHICOPEE, MA
- Parts Used:
- 240495804
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
None fit perfectly
Just slid it down into place.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Pat from LAGO VISTA, TX
- Parts Used:
- 240356501
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Plastic runner broken
Got the part. Watched the video. Replaced the Meat Drawer Rail. Just lke that! Easy squeezy! Thank you for making it so simple! ***** (that's five stars!)
Was this instruction helpful to you?
Thank you for voting!