1068490012 Kenmore Refrigerator - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Patricia A. from Toccoa, GA
- Parts Used:
- WP2198202
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Screw drivers
Our refrigerator failed to cool in stages, finally quitting to cool or run.
First, after re-reading your descriptions here on your site ( it took clues from each of them) I unplugged the refrigerator and began on the only day my husband was out of town. The two selector knobs came off easily fingers only. The plate came off with only a slight prying with a screwdriver (it is intended to snap off this way). Loosening the screws and removing them in order to remember which order they returned proved to be a challenge. After disassembly, pulling the thermostat out of the tubing and replacing it with the new one without bending it was hard to do also. The refrigerator runs like new, and may run another eleven years! Thanks!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- David from MARYLAND HTS, MO
- Parts Used:
- WPW10662129
- Difficulty Level:
- Very Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver
freezer (later fridge too) wouldn't stay cold~
****Make are you order Capacitor & Starter relay too (we ordered separtely so had to pay shipping twice)**** Super easy just open access panel on back near compressor and remove retention clip with fingers, remove & replace both capacitor & starter, put clip and access panel back on, plug in and allow 8 hours to cool! Works like new again! Hope it goes another 10 years
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Michael from HELENDALE, CA
- Parts Used:
- WPW10662129
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Screw drivers
freezer would not freeze
inst said,"50 pct of the time this calls for new capacitor," so we changed the capacitor. Same prob. It also said,"25 pct of the time it's the bi-metal thermostat" So we ordered it. We removed the plastic rear panel from inside the freezer comp. using small nut driver. Here we found much ICE surrounding the defrost unit, three inches thick. We thawed the whole mess. and the freezer has worked fine ever since. I think my habit of getting ice cubes from the inside container rather than from the ice cube dispenser, had kep t the freezer door open too much, interfering with the normal defrost cycle and allowing ice to build up over time so that it finally defeated the system. My new rule, "get ice cubes only from the front."
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Cecelia from Garden City, TX
- Parts Used:
- W10822278
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
Freezer made lots of Ice and Refrigerator didn't cool
The Defrost Timer is located in Refrigerator section (not the freezer) where your temperture guages are. Move panel and replace the non working Defrost Timer with the new one. It took my husband about 30-40 mins to fix. This was about 2 weeks ago and my Freezer and Refrigerator are working like new. I bought this Kenmore Reftigerator brand new in 1996 and I lost the manuel to it. Thanks to my daughter who found the Defrost Timer on the Internet, I thought I was going to have to buy a new one. This was real easy to fix. The instructions that came with the part was easy to understand and very self explanatory. It also had very good diagrams to follow.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Milton from NEW YORK, NY
- Parts Used:
- WP2198202
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Pliers, Screw drivers, Socket set
needed termastat
your video made it very easy...Thank You
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- stefan from BLOOMINGBURG, NY
- Parts Used:
- WP2198202
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Pliers, Screw drivers, Socket set
Thermostat stopped working. Only cooled at highest setting.
Repair video was excellent but thermostat unit was slightly different then original. Fortunately guessed right regarding connections. Also very difficult to place the insulating plastic on wiring. Not very smooth. Also removing panel was different then in video. Needed to remove the panel to reveal two screws underneath that need to be removed along with the ones at the ceiling.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Steve from Fallbrook, CA
- Parts Used:
- WP2198202
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Pliers, Screw drivers, Socket set
Frig did not turn off (stay running all the time) but originally did not run until I wiggled the temp nob
Just followed the Video I found on your site. Seems to work good now, took awhile to get temp setting correct (had to set it a little colder about half way between the "b" and "c" setting).
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- pat from sayner, WI
- Parts Used:
- WP2198202
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Screw drivers
fridge was too hot or too cold
replaced tsat
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Dawn from RED WING, MN
- Parts Used:
- 4388538
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Pliers
Broken support on lower drawer shelf.
Important: Do not twist broken stud to remove if possible, just pull with the pliers straight out. I twisted it and made the hole larger. Even so, I just used Gorilla Epoxy glue to secure the new one (follow directions on the package) and it's fixed. It's been a couple days and still looks secure. Thanks for the quick delivery.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Dewey from TOMAHAWK, KY
- Parts Used:
- WP2198202
- Difficulty Level:
- Easy
- Total Repair Time:
- 1- 2 hours
- Tools:
- Nutdriver, Pliers, Screw drivers
Refrigerator was not cycling on and off properly, allowing food to thaw.
I followed the directions given in the video.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- William from CARROLLTON, GA
- Parts Used:
- WP2198202
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Screw drivers
Freezer would go from zero to 55 degrees. Ruined all my food.
Followed instructions in video.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- RAUL from MIAMI, FL
- Parts Used:
- 4388538
- Difficulty Level:
- Very Difficult
- Total Repair Time:
- More than 2 hours
- Tools:
- Pliers, Wrench set
the broken stud was very hard to remove, no instrucitons anywhere
only the front right stud was broken with very little left attached to hold and remove. After a long twist and pull , got it out and placed the new one....
Still recommend Part Select..RAUL, MIAMI FL
Still recommend Part Select..RAUL, MIAMI FL
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- anthony from NORCROSS, GA
- Parts Used:
- W10822278
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Screw drivers
Freezer no longer frost free.
Reviewed Youtube video as a reference. Unplugged refrigerator. Removed old defrost timer. Matched the color of the wiring harness to the diagram that came with the part. Attach new part to wiring harness.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Doug from Lancaster, CA
- Parts Used:
- WPW10662129
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
compressor not running
Removed the access panel on back of unit located the Run Capacitor on the compressor and removed the bad one and put the new one on and pugged refrigerator back in and it started up and works fine now
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Anthony from CIRCLEVILLE, OH
- Parts Used:
- 819100
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers
freezer quit working
replaced relay switch
when I finally got started to do the repair it took 15 minutes my biggest delay was no instructions were sent with the part and it took time to get some
when I finally got started to do the repair it took 15 minutes my biggest delay was no instructions were sent with the part and it took time to get some
Was this instruction helpful to you?
Thank you for voting!