25368132890 Kenmore Refrigerator - Instructions

It snapped in place.

took 4 screws out of the discharge vent on top of the refrigerator section and unpluged the wiring harness and put the section on the counter and unscrewed the timer and put the new one in and reinstalled the assembly and plugged the Jack and put the 4 screws back in, and rotated the timer and put it on defrost removed the back and check the heaters and drain .

removed everything from door, removed screws in gasket around door, laid door face down(insulation side up)applied rtv around edge of gasket and door, waited 10 minutes and started with top screw in middle of top then middle of sides and bottom then installed remaining screws checked levelness of refrigerator, the you are done

Unplug the refrigerator. Removed the right hand top shelf. Used a 1/4" nutdriver to remove rear center mounting screw for Control Housing. Used Phillips screwdriver to remove two mounting screws for timer. Unplug cable from timer and plug it into the new timer. Install the new timer and re-install the Control Housing. Plug in the refrigerator and adjust the timer to start the unit. This was a snap with the diagnostic provided by Part Select. At first I thought it was the fan rubbing but when I removed the cover (two screws) it was obvious that wasn't the problem. The diagnostic hinted that it was either the timer or the motor capacitor making the noise. Because the noise continued after turning OFF the control, I thought it was the timer...I was right.

Having looked at the broken area, in some frustration, for several years, I had a good idea how it all went together: the front end slips over a metal lip suspended from the front of the shelf above, and the rear is held in place by a single screw (single slot with hex-dead). The most time was taken clearing the items off the shelf above. Having done that, the shelf was easily lifted up and removed. Flip it over to expose the screw at the back. Remove that screw and discard the old/broken hanging rail. Slip the front end of the new rail (carefully) over the metal lip. At the rear, line up the hole on the hanger with the hole in the mounting bracket and re-insert the one screw. Re-install shelf and slide the drawer back into place on the hangers. Good to go.

I went on partselect put in make and model number, a list showed the probable cause. I watched the how to video. When I received the part in short order I loosened 2 screws disconnected the wiring plug (sprayed it with contact cleaner) pluged it in, removed screws from old part put them in new one. Put timer back in its location and tightened the screws. Very eazy, works fine.

I pick up very fast at these kind of small jobs but because of my very busy schedule I decided to call (2 times) technicians about my problem but none of them had any idea. About my repair, I removed the grill at the bottom of the refrigerator, unscrew a small plate (located on the bottom left side) that's holding the defrost timer. I plug on the new part, screw back the plate with the defrost timer and that was it. Don't forget to turn clockwise with your finger the timer until you hear a "click" and then turn it slightly more to the right. There is also a video on U-tube.

open freezer door two screws just below unscrew slide piece to side unplug reinstall very simple.

Unplugged the frig. Removed temp control module from frig, 1 screw with nut driver. Activated defrost timer by rotating adjustment until 2 clicks are heard. Removed two timer mounting screws, unpluged timer, plugged in the new timer, mounted it to the control module with 2 mounting screws. Replaced control module with the 1 mounting screw. Closed door and plugged it up.

Problem not consistent. OK for 2-3 weeks, then freeze coils. Mark and observe the defrost timers manual rotating adjuster. Timer would stop mid cycle. One revolution equals 8 hours of compressor run time followed by 30 minutes of defrost. Replacing timer took 5 minutes.

Decided to clean the refrigerator at the same time as replacing the broken part. Took shelf out, removed glass, washed all parts, removed broken rail (two screws) and replaced new part. Piece of cake!

I first thought the defroster heater broke - took the back wall of the freezer off and cooling fins were fine. Then took the defroster timer out and opened it up. The contacts were badly burnt so the compressor and fan ran during only part of the cooling cycle. Replacing the timer took less than 5 minutes - turn off the power, remove one screw to take out the control box, cut the ground wire (new timer housing is plastic and does not have a ground connection), remove two screws to unmount the timer, unplug the old timer, plug in the new timer, fasten with two screws, put the control unit in and fasten with one screw, turn power back on.

real easy with the help of the video , made the difference

You guys at Partselect are the best!!! Went to your site, typed in my appliance symptoms, and received possible fixes. Ordered the suggested parts (under $50) on a Sunday night and got em Tuesday am. Installed the easiest one first and Voila!!!! Frig is working great. Thanks Bob S

Remove 4 screws that hold up overhead controls, this is also the part that holds the light. Unplug the timer and replace. Super simple and runs great now. After you plug it in it may take a few minutes to kick on the compressor but it will. Also I was pleased it was a factory Frigidare part. Price was right.