25358085890 Kenmore Refrigerator - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Janis from Conroe, TX
- Parts Used:
- 218904404
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver
Filter housing was cracked & water was leaking all over the refrigerator
First I turned off the water supply to the frig and raised the bar in the ice make to stop the production of ice. I used the nut driver to remove 3 screws from the housing. I removed the connections from the two water lines & removed the broken housing. I attached the water lines to the new housing and then screwed it back into the refrigerator. I replaced the filter and screwed the filter cup into the housing. Turned on water & ice maker, then ran water thru the door dispenser to check to see if I had done it correctly. No leaks !!! Yeah....I was done !!!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Doug from Folsom, CA
- Parts Used:
- 215846602
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Fridge side warm. Freezer was ok.
Popped off the front plastic cover on the bottom of the fridge, under the doors. Two screws held the defrost timer on under the front side of fridge (below freezer door). You can't really see the timer except for the adjustment knob that is accessible through a hole. Once the screws are removed, disconnect the wire plug and remove and replaced unit. Works fine ever since.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Vaughn from Virginia Beach, VA
- Parts Used:
- 218518700
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Socket set
Leak in the water tube elbow
First I remove protection cover,then removed the elbow pressing in on the gray coupling housing at each end of the elbow.Mark each piece of water hose before removing the elbow with marker(black)it helps when replacing new elbow.The new elbow slides on each end of water hose ,connect the end to the hose coming out of the door first. Replace protection cover. No more leak.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Randy from Great Falls, MT
- Parts Used:
- 218658000
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver, Pliers
My ice maker quit making ice.
I removed an access panel loosened the two screws that was mounting the water valve to the refer frame. I took off the three lines to the valve and unplugged the wires from it and reinstalled the new valve. The whole job took 5 minutes.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Robert H. from Grand Blanc, MI
- Parts Used:
- 297216600
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
frezer not staying cold enough to freze newly added product
took the shelves out, unscrewed the rear panel,unpluged the thermistat and uncliped it from the line.Replaced with new thermistat in the reverse order. Before turning the unit back on,allowed the coils to defrost.All of the process was shown in your vidio that I was able to view while ordering the part. Thank you
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Bob from Milton, WV
- Parts Used:
- 241885001
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
housing-crusher was broken
removed ice maker box and disassembled crusher unit on front of box and installed new housing.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Thomas from Niceville, FL
- Parts Used:
- 241734001
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
There was a hole in the plastic bin where ice fell through to the freezer.
I removed the screws that held the the ice dispencer from the bin. I than removed three screws from the bottom of the bin. I put the new plastic piece on the end of the spiral piece that
pushes the ice. I inserted the spiral piece back into the hole. I than screwed the ice dispencer
to the bin and re-inserted it back in the refrigerator.
It took me about 5 to 10 minutes. It's really easy!
pushes the ice. I inserted the spiral piece back into the hole. I than screwed the ice dispencer
to the bin and re-inserted it back in the refrigerator.
It took me about 5 to 10 minutes. It's really easy!
Was this instruction helpful to you?
Thank you for voting!
Rust had corroded Front Plate and Drive Blade
Installation was completed by following the online Parts diagram. Had to completely remove all parts, including the blades in ice crusher, and re-assemble. Glad the online diagram was clear and easy to read.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Larry from Cordova, TN
- Parts Used:
- 218740003
- Difficulty Level:
- Easy
- Total Repair Time:
- 1- 2 hours
- Tools:
- Pliers, Screw drivers
The ice would not come out of the front door. The flap between the door and the ice would not open.
Popped off the front access panel. Removed the heat motor and repalced with the new one. It is fixed and working great. Partselect Delivered the part the day after I ordered it. Thanks!!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- bill from wilmette, IL
- Parts Used:
- 5303917278
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Socket set
Fridge And Freezer Not Cool Enough
Unplug fan and remove 3 bolts. I had to bend the fan frame in order to remove fan. Change fan blade and reverse procedure. Fridge is fixed nice and cold
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Guy from Califon, NJ
- Parts Used:
- 215501901
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver
Condensor fan motor failed
Removed the old fan--three small nuts and snap off connection. Ordered part and received the next day. Your company is great!!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jeffrey from Indianapolis, IN
- Parts Used:
- 5303918277
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver
Ice maker was not making ice
I replaced the solenoid first because the ice maker was not getting water. After replacing the solenoid valve, I waited about 1/2 an hour, still no water. So, I ordered a replacement ice maker. I then installed the replacement ice maker, waited a 1/2 an hour, still no water. Then, I waited overnight. Yeah, ice! WORD OF ADVICE. WAIT OVERNIGHT TO SEE IF THE ICE MAKER CREATES ICE. Not sure how long a cycle takes, but it's longer than you would think. Hope your installation is a success!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Dung David from Phoenix, AZ
- Parts Used:
- WFCB
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
replace old water filter
The untwisted the water filter took out the old water filter and replaced it with the new one and twisted the cover back on. it was very easy to do and now the water tastes very fresh :) thank you
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Mary from SOUTH LYON, MI
- Parts Used:
- 241798231
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver, Screw drivers
Ice maker failed
Watched YouTube video. Very easy. Used my cell phone camera in ‘selfie’ mode propped up in the upper right hand corner of freezer to see the 2 hidden screws.
Was this instruction helpful to you?
Thank you for voting!
broken end caps
The end caps worked perfectly for both the Frigidaire and Westinghouse fridges. Just pulled out the old end caps and then literally just pushed in the new ones (remember to attach the shelf bar before attaching the second end cap!). The pieces arrived quicker than expected. Thanks Partselect!
Was this instruction helpful to you?
Thank you for voting!