10651339716 Kenmore Refrigerator - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- John from DUNNELLON, FL
- Parts Used:
- WP2198628
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Pliers, Socket set
Ice maker grinder motor was not running.
Remove the ice bucket and check that the auger that turns in the ice bucket is free to turn. Cover the open freezer with cardboard or whatever to retain most of the freezer temperature. Remove the holder that supports the top of the motor shaft. Check the splines on the upper part of the motor shaft and also check the seal under the holder. Open the access the door to the motor, remove wiring connector and unbolt the motor. Check the lower splines on motor shaft for condition, clean the shaft and apply new grease to the splines. Before installing, connect the wiring to the new motor, push the door switch in, press the ice dispenser arm outside the door to make sure the motor runs. If all ok, check the motor shaft for fit in the new motor. Be careful not to install the motor shaft too deep in the motor splines, otherwise there may not be enough spline showing on the top end to engage the auger. Bolt the motor in place, close access door and install the holder and ice bucket and make sure everything works. If there is not enough spline showing thru the holder to engage the auger, take pliers and pull the shaft up a bit. This seems to be a hit or miss fit on the shaft but you can adjust the height of the shaft without taking every thing apart again. That's all, not difficult at all. But do check parts and pieces for anything else you might need, parts wise, before ordering the motor by itself like I did. Shipping is high, so try to order any associated parts needed when you order the motor. By the way, This site are great to work with!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- John from AUBURN, CA
- Parts Used:
- W11396033
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Screw drivers
Refer lights not working, there are two lights and neither worked. Decided the switch was the problem.
The switch fix but did not fix the problem. I assumed the wires go on the same way as on the old switch. Is it possible if one light Burns out, the other will not work either?
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- RALPH from PARAMUS, NJ
- Parts Used:
- W11396033
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Refrigerator lamp not functioning
Had to push the light switch to get lamp to light up.
Removed power from refrig. and removed old light switch
and replaced with the one I got from Partselect. Turned power back on and was done.
Removed power from refrig. and removed old light switch
and replaced with the one I got from Partselect. Turned power back on and was done.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Richard from HOLLISTER, CA
- Parts Used:
- WP2176759
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
Noise in Evaporator Fan section
Opening up the Evaporator Fan section was a quick and easy job. After opening, I checked and removed the fan and looked at the grommet. The grommet on the fan was tight and secure and I could no longer hear the noise. I closed the opening. Something I had done while checking the fan grommet must have solved the problem. I have not hear the noise again!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- James from Shrewsbury, MA
- Parts Used:
- W11396033
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
Broken light switch
Pried out the old switch and installed the new switch.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Justin from Huntersville, NC
- Parts Used:
- W11396033
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Light hinge broke
Repair was tremendously easy. All I did was remove old light switch by prying out with screw driver and plugging in the new light switch and pushing it into the hole. Simple! The instructions weren't needed, but they were very thorough.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Harold from Lindenhurst, IL
- Parts Used:
- W11396033
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Pliers, Screw drivers
icemaker
installed new parts
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jack from Topsail Beach, NC
- Parts Used:
- W11396033
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Broken refrigerator compartment light switch.
The best part of the repair was how easy it was to find and order the part. Instead of searching the parts houses around town I just went to the PartSelect web site, quickly found and ordered the part in about five minutes, received the part the next day at my home and was ready to make the repair. Wow! What a pleasure for something to work the way it was meant to. Removed old switch located by prying out with sharp knife or screwdriver. Don't worry about breaking it or cracking plastic. Disconnect(unplug) wires from back of switch. Replace (plug-in) wires on back of new switch. Insert in location of old switch. Finisheed.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- chris from woodland hills, CA
- Parts Used:
- WPW10662129
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver
you have to turn it off and on to run.
Just like the video showed me.It still does not work. Have to turn it off and on to make it start up.I also replaced thermostat in freezer. Does not work.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Richard from Smyrna, GA
- Parts Used:
- W11396033
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
Frost in bottom freezer, freezer 8%, ice maker works
replaced electric control board, defrost for six hours. next day (24 hours) same problem, dusterhoff2928@charter.net
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- WES from SPRINGVILLE, AL
- Parts Used:
- W11396033
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Switch Controlling Light When Door Open Was Briken
Poped ou the old switch, connected new switch and pushed back into socket.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Keith from Racine, WI
- Parts Used:
- W11396033
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Light switch broken
I used a knife blade to slip under the edge of old switch to pray it out of the hole it was inserted into, switched the wires and replaced the new switch into the same hole. It took about five minutes!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Matthew from Buffalo, NY
- Parts Used:
- W11396033
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Screw drivers
Broke plastic tab on auto light switch
Used screw driver to pop out old switch. Used pliers to hold wire connection from fall back into slot on fridge. Inserted new swith into plug and pressed new switch back in place.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Richard from CONYERS, GA
- Parts Used:
- WP2176759
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 1- 2 hours
- Tools:
- Screw drivers
The ice dispenser handle wasn't working properly. Sometime when dispenser handle was pressed it didn't dispense ice on the first try.
I installed a Ice Door Kit. It works Great Now!
Was this instruction helpful to you?
Thank you for voting!