59667277790 Kenmore Refrigerator - Instructions

I removes all food and drink items from the refrigerator and freezer doors. I then removed all of the screws holding the inner panel of the refrigerator door to the door itself. The old gasket could then be removed. I placed the new door gasket in place around the inner panel and reinstalled the inner panel with new gasket onto the refrigerator door. I then removed the inner panel from the freezer door and then removed the old gasket. I placed the new door gasket in place around the inner panel and reinstalled the inner panel with new gasket onto the freezer door. I used a portable drill with a 1/4 inch nut driver to remove and reinstall the many screws that held the inner panel and gasket on the doors.

Overall, replacing the ice maker wasn't too bad but it wasn't nearly as easy for me as it seems to have been for some. In my case, the fridge was an Amana and the ice maker was mounted in such a way that disconnecting the power connector was difficult. The ice maker had to be completely dismounted before any access to the power connector was even possible. The short power cables made it very difficult to get the ice maker into a position where I had a good view of the power connector enabling me to see how to release it. The only other challenge was the cup that the water line goes into. The replacement ice maker did not come with the right cup - the instructions said to replace the provided one with the old one. No instructions for this procedure were provided and it looked to me like it might involve significant disassembly, something I wanted to avoid for fear of breaking a plastic part on the new ice maker (something I had already done when disassembling the old ice maker). So instead of replacing the cup, I modified the new one to match the old one. This involved removing a cutout on one side and covering a hole on the other. Installation of the new ice maker went fine and the water leak problem was fixed.

R & R Icemaker Assembly. Took out 3 screws and unpluged Icemaker & replaced with new part. very easy and the service from PartSelect was fantastic.
Very Satisfied,
Ron Martin

Icecubes came out half-way, and refrooze. I figured out, that the melter does not work (HEATER in the icemaker) Voltage measured 105V no load. Studied the Internet, and folloved an advice: shorted the back wire and the blackwire with white stripes.these go to relay contacts. It seems, that the relay contacts are no good on Infrared receiver boaed. I turn off manually the icemaker, when needed

Because the refrigerator worked (38-40 degrees) and the freezer only got down to 29 degrees, I thought that the freezer thermostat had gone bad. Changed it out but results are the same.

Soaked the gaskets in bathtub to make them more pliable. They laid flatter and were easier towork with,

It turned out the water valve was not the problem but I think it works a bit better with the new one. I had replaced the main part of the icemaker inside the freezer which had lost the smooth finish in the ice tray. It worked for awhile but quit.
What had happened was the large approx. 1/2 inch tube going from the back of the refrigerator to the icemaker tray became plugged with ice. It was difficult to get it out due to the ice but once I did it was easy to melt it and put it back together. All's well that ends well and avoid the cost of a repair call. Working great now.

Had to disassemble ice maker to install part. . .

The good news is that the part (the wheel was available.) I bought two in the event that the other wheel may break in the future. The bad news is that the housing that holds the wheel was riveted together by the wheel axle. It would have been nice to know that before I bought the part and if the housing with the wheel installed was available. The refrigerator was at my summer house a hundred miles away. Anyway, we had to grind the end of the riveted axle to dislodge it from the wheel housing. With the axle dislodged from the housing we were able to install the wheel and then hammer the end of the axle flat to keep in place, like the original rivet installation. It is not perfect but it held and should be fine. I am glad I was able to get the part and will be back in the future, if in need of other parts.

It was so easy!

Thanks for the rush to my home on the part.

I just unscrewed the plate that locks in the light switch (screwdriver) and unplugged the old faulty part and plugged in the new switch, screwed the cover back on and I was done!

Easy!

And I am not Mr. Fix-it!

Removed screws on back cover plate in Freezer, disconnected fan assembly, removed fan assembly, removed propeller from fan assembly, and transferred it to new motor, installed new assembly, reconnected electrical connections, screwed on back cover plate - Viola!

turn off water and unplug fridge. remove ice maker bottom mounting screw. just loosen the 2 top mounting screws. unplug wire harness from back of fridge. remove old icemaker from freezer compartment. once removed, salvage square endcover and reinstall on new maker. unfasten wire harness from old maker and reinsatll on new one. reinsert thermal wire in new ice maker holding bracket. remove second wiring bracket and reinstall on new maker to hold remaining wires (not mentioned on "how to-" video). remove old ice maker on/off bale and reinstall on new one. remount new maker to top mounting screws, reinsert harness plug into fridge. replace bottom screw,

First it required defrosting since the cooling area was solid ice. Note that I replaced the defrost timer first and no difference. I pulled the icemaker and racks out, then removed the door by removing the 4 screws with 1/4" nut driver. One of the sliding drawer tracks must be removed in order to get the back panel in/ out easily. The 4 screws were easily removed with my nutdriver. The screws are not all the same so keep track! Next remove the 4 screws that hold in the vent assembly where the cold air shoots out (center). Remove all of the remaining screws in the panel in the rear of the freezer compartment and pull it out. The themostat is on the right side with 2 wires and a clip that holds it on to the coolant pipe. Pull it off of the pipe and locate the connector - 5-6" from the thermostat. Pull connector apart without damaging the wires inside. Install new part the same way the old one came out and reassemble in reverse order.

First I removed the back cover then removed 3 nuts holding the motor. Next I removed the two wires. Next I attached new connectors to the wires and installed the new motor and everything worked perfect!

Service and shipping were fantastic! I would definitely use Partselect again!

I have replaced the circuit board, the condenser fan motor but the unit still will not feeze correctly. The bottom of the unit freezes but just barely cools the rest of the freezer and ice box. Have you got any other advice that might help. This is a side by side unit. What else could be the problem. It seems that the fan is not working correctly or it is stuck in defrost mode. The coils where the fan is seem to be icing up but it will not let the fan work. THanks for your help, David Wilson