1067680780 Kenmore Refrigerator - Instructions

removed two screws and pulled part out of the unit. The local appliance store said they needed model and part # to try to identify and order the part. Found part select online, found the part immediately, ordered the part for $4.50 or so. Part was delivered in 2 days! Very easy installation and the part works perfectly. Thanks so much!

Removed the screws and disconnected the electric. I put the proper electric harness on and went to fit the unit in but it didn't fit. Until I figured out that you have to use the clips from the old unit that hold the unit in place. The actually hang on them. Once I figured it out it was easy.

I purchased the part and put it in,

On my particular model refrigerator I only needed to remove one screw and disconnet the plug. I then slid the unit out. The new ice maker did not come with the plastic sled that was attached to the old unit. I removed and attached the sled to the new unit with 3 screws.

The instructions are practically no help, but if you study the diagram, you can figure out the one screw you need to remove. Then the icemaker lift off of two brackets. I couldn't see how to use a screwdriver to unlock the bracket, but just applying mild pressure and pulling it forward brought it right out. I didn't have to change anything with the plug already intalled so it was very easy to pop in, lock the plug, pop into brackets, replace screw and I was in business. 24 hours later I had a bucket of ice! 15 minutes to figure out how to get old out and 5 min to replace new one. Fairly easy. Read posts here to get hints!

removed three screws pluged it in and it was ready to go. I must add That I ordered it one day and received it the next day by fed ex. I could not believ how fast the service was also the new icemaker is working great. I will order any furture parts I need from Parts Select. Also have given your web site ot several other people. Thank you very much.

Ice maker wouldn't eject the ice often enough. After reading a few other stories, I just ordered the universal ice maker from Part Select. All I had to do was remove some of the plastic shrouds from my old ice maker and put them on the new one. I also reused my mounting brackets. The whole job took me 20 minutes.

removed back cover, removed fan motor and replaced with new one. connected new power wires. worked right away

The plastic part that connects the fresh cold water to the ice maker in back of the fridge cracked.
Do to the fact that Whirlpool has the part stick out on the back top part of the fridge. So if you push the fridge just an inch too far back the plastic part will crack.
I ordered (The Part S&H)- came to about, $11.00.

1. Turned off the cold water under the sink.
2. In the back of the freezer section. I unscrewed the two screws that held the old broken part to the fridge.
3. I opened the freezer section and cleared out the top shelf till I could see the back of the fridge.
4. I removed the old plastic part by pushing & wiggling it about forward and it then extended out the back of the freezer side and then I pulled it out the back and it came out.
5. I slid the new replacement part in basically the reverse of step 4.
6. I connected the hose in the back. To the new, replacement plastic part, that fills the automatic ice tray with water.

7. Once finished I glued a small 2”x2” piece of wood next to the new part so the fridge will never get too close to the back wall so to never break that part that sticks out again.
Before just a small bump could break the part and water is everywhere and this leak could happen slowly at first and the next day what a mess.
Some fridges have this part recessed into the back of the fridge so this would never happen as my other fridge has.
Also, this might seem like more work then it was. It was very simple. I was scared I'd screw it up, but just did it step by step. If I had someone do it. It would have cost me a bundle.
It took more time to type this, then to do the work.
I had no instructions to follow, but again, was easer then I thought it would be.
I hope that this was helpful,
Jim Vourakis

i noticed that no water was getting to the ice maker. rather than messing around with parts, i bought the entire unit. easy to remove old one and install new one. thanks...ice started again in about an hour. unit cost less than a service call!

I took out the old socket by moving a clip. Reattached the electrical wires, clicked in the socket and that was it.

It was exactly as everyone else described--remove old ice maker, unplug, plug in new ice maker, attach new ice maker. 3 screws, 1 plug. My plug was the one on the ice maker not on the refrigerator (ie I used the wiring/plug that was already in the freezer).

Order the part from the Internet on Sunday, it mailed out on Monday and I received it on Tuesday. I unplugged the fan then undone 3 screws that held the fan bracket to the refrigerator pulled it out unscrewed 3 more nuts and replaced the fan on the bracket and I cut the old wire plug off the old fan and with 2 wire nuts put it on my new fan. Replaced the fan and bracket back on the refrigerator plugged it in and it works like a new refrigerator.

Simlpy removed two screws to remove the old part. replaced the new part and put the two screws in. Job finished.

I loosened the two screws on which the ice makers hangs and removed the third screw toward the back. I lifted the icemaker a bit and removed the part and unplugged the unit at rear. I reversed the process to install the new one. All very simple.

At first nothing happened, no water filling the tray. I thought there must be some other problem. A few hours later I heard ice being dumped into the ice container. I don't understand the delay but it works fine.



At first no