2538791212 Kenmore Refrigerator - Instructions

Fast and easy. Started by pulling out refrigerator and unplugging it. Water valve for ice maker was already turned off due to leaking. Disconnected old valve, detached old valve, reattached new valve and reconnected water lines. Bled the lines and turned back on. Make sure temp in freezer stays at recommended temps for ice making.

According to the online video instructions.

I watched the video and did the same thing on mine and now it is working fine

1-Unpluged the refrigerator 2- removed ice cube tray and some food( Placed in cooler )3- unscrewed the two screws holding the old unit lowering it and unplugged it. 4- Had to loosen the cooling coil to get to the pass through hole in the back and pulled the old wire out. Connected the wire adaptor to the old connectorand to the new ice maker. At this point I couldn`t pass the new plug through the back so I strapped it out of the way and installed the new ice maker using the two screws from the old one. Adjusted the fill adjustment and turned it on. Cubes in about 4 hours.

This would have been an easy repair, but I bought the Frig from Lowes and I think they added the icemaker. The replacement icemaker uint has a plug on it for easy replacement. My frig was hard wired so I had to cut off the plug and splice the wires. Not a real big deal but a small work space.

Took less than 10 min to install following the inclosed instructions. At first it was not making enough ice to make me happy so I set the temp. a little colder in freezer. Now making ice like crazy. Works better than the old one ever did. Very happy with the new replacement.

moved freezer items to right of icemaker,loosen two nuts lifted icemaker over nuts,squeezed and pulled cable out turned over marked L bracket screw with marker for location plugged cable in tighten screws,made ice in 2 1/2 hours john

I noticed that the two gears weren't meshing together so upon inspection I saw that one of the gears had an inner piece missing making it weak so it kept popping out away from the other great. I ordered the new gear and unscrewed the old one off and put the new one on. So easy. It made Ice beautiful after that

We reviewed the video posted on your site for guidance. It was very helpful to see someone do the repair. The project went just as described in the video. Within 24 hours I had a full bin of ice!

1st my 72 year old husband has not had great success in repairing anything: electrical or plumbing. We got the part the next day. Had ordered it late one afternoon and had it the next morning in Wyoming. From the time we took it out of the box, disconnected the old one, plugged in the new one, remounted, it took less than 15 minutes. Amazing and it works great. Didn't need extra electrical connector, but tricky part on electrical connectors is to squeeze side to take apart and put back together. He used mirror to see the screws to loosen to take out and put back in ice maker. Next day our tray was full of ice. Good service/Good Product.

Tested for power and found the thermal cut-off bad. Installed new one.

Unplug refrigerator power cord. Remove ice cube bin. Place wire signal arm in down (off) position. Ice Maker is held in place by two (slotted/hex headed) screws through keyhole slots over the top of Ice maker along the left side of freezer. Use mirror to locate screws then carefully loosen (do not remove) screws with a nut driver or screw driver. Lift Ice maker up and right until it releases from the screw heads. Unplug electrical connection. A flat screw driver may be required to loosen connector. Connect new unit electrical and Install new unit over screw heads and tighten screws. Replace Ice Bin and place wire signal arm in the up (on) position. Reconnect refrigerator power cord. After freezer cools down sufficiently it will start making ice.

instructions were very simple. Took about 10 minutes to replace the unit. Do NOT get excited about immediate ice because it took mine awhile to g et cranked up for full production. Anyone can do this! Saves about $150.00 in labor to have someone(no smarter than you) do it for you.

Replaced ice maker - easy to replace but it did not fix the problem.

The repair went exactly as illustrated by the video offered by part select. That video was helpful and showed me step by step how to accomplish the repair. The replacement part was exactly the same as the original, thank you part select.( Allow the old ice maker to return to room temperature before you remove the 1/4 nut securing the level mechanism, otherwise the frozen head of the not will break off).