1066669300 Kenmore Refrigerator - Instructions

removed the three screws holding the old ice maker in place - unpluged the electronics .... took the new ice maker pluged in the electronics screwed in into place and we were in business and had ice within an hour.

I removed the two attachment screws and lifted the old icemaker out and disconnected the plug. The new one was identical to the old one so the installation was just a reversal of the removal. The water soleniod was sticking from not being used so I took it apart and cleaned it. The next morning I had ice. The part arrived at my door in less than 24 hours from my order placement.

Wathced video (VERY helpful)of how to do repair to make sure it was within my capabilities to do. Made sure I had all requested numbers before ordering. Replacement part was an EXACT fit. 15 minutes of work and I saved nearly $150 of estimate by local service company. I am (and will continue to be) a repeat customer. Thanks. Mel

put arm up to stop icemaker from creating new ice cubes. us nut driver to unscrew 3 of the nuts holding icemaker in place do not completely remove the 2 top screws. lift off the screws and unplug from inside wire connection...make sure water tub is removed and frig unplugged. clean off ice anywhere inside freezer...take out new icemaker and connect wire plug...attach icemaker on to the 2 top screws...use nut driver to tighten into place. add and tighten bottom screw...leave arm down...replace clean and dried water tube into back and make sure it slid into ice maker...tighten screws in back and attatch water hose to tube...plug frid back on slide back into place...will start making ice in an hr or so....

I used a phillips screw driver, took the old one off, replaced the new one and it worked immediately!!! Didn't have to turn anything off...fixed in 5 minutes for $11. Fantastic Experience and my husband was shocked. No repairman bill.

It actually took me longer to think about the repair than actually doing it. It was three screws, two upper that you just loosen and then one on the bottom that you remove. Pulled the unit out and disconnected the power. Slipped the new unit onto the two upper brackets, after connecting the power cord, tightened the bracket screws, reattached the bottom set screw and I was making ice. Incredibly easy. When I ordered the replacement unit they said it would arrive in 3-5 days, but it only took a day and a half. Great experience all the way through. I'm a customer for life.

We followed the video on the KitchenAid website. We turned off water valve at the wall, unplugged the refrigerator, removed the old icemaker by unscrewing the three mounting screws. We unplugged old icemaker from electrical source at back of refrigerator freezer compartment and removed it. We detached the on/off bar from the old icemaker and installed it on the new icemaker. The new icemaker fit perfectly. We plugged in the electric wire to the existing power cord at the back of the refrigerator freezer compartment. We placed the new icemaker in the same position as the old, making sure the mounting screw holes were aligned. Plugged refrigerator back in and turned on the water. Works beautifully.

Pop off six mounting screws and the ground screw. Remove the fan blade and reattach. Reinstall. Save yourself big bucks.

I removed the 2 screws on top and the one screw underneath holding the Ice Maker to the wall of freezer.I pulled the electrical connection from the wall next (wiggled it back and forth until it came out).
I matched it up to the picture from this site and ordered the replacement unit.
When it arrived, it had a lot of extra parts to match up to mine and any other fridge.
A good tip is to keep the old unit so you can configure the new unit the same. Although it was easy, this took me the longest of the entire job. Once this was done, it took me !0 minutes to plug the new unit into my fridge and then attach it back to the wall with the 3 screws.Not a hard job.Thanks

I replaced the defrost relay folling instructions I read on the internet--and it still didn't work--So I replaced the compressor start relay which was easier than the defrost relay--it worked and the fridg is working good.

It's self-explanatory. The procedure is obvious; it's just a little difficult. The only hard part is attaching the mounting brackets to the fan. If you can't tighten the mounting bolts, loosen them and reposition the brackets. You might end up mispositioning them at first, because they are hard to reach.

First I turned off water supply. Then removed the two screws that attach ice maker, then disconnected the wiring harness.

Attached new ice maker in reverse order.

First I removed all the screws from the back cover.
2nd removed fan nut and fan blade
3rd removed fan bracket
4th I traced wire to the condenser and disconnected wires from wire nuts.
Installed existing fan brackets to new motor kit
then reconnected wire nuts to new motor cord
Reinstalled fan nut and blade,
reinstalled cover, plugged it in and BAM .WORKS PERF!

Replaced the water valve. I knew that the ice maker was working by watching the movement. It was not getting water to it, s I figured it was the electric water valve and sure enough, that fixed the problem.

Looking at the instructions it looked like I had to rewire the the plug in the adapter. As it turns out, you don't .Using a screw driver, I released the braket mount and the nut driver loosened the nut holding the tray to the wall. It came right off when you lift it straight up and the wire assembly was exactly the same as the original. All I did was plug in the new ice maker, Hang the assembly on the loosen nuts and tighten again and put the screw back in the bottom bracket that held it in place. I spent longer looking at the instructions than I actually did in the whole replacement time. By morning we had a good amount of ice. EASY>>