2539301791 Kenmore Refrigerator - Instructions

Fast and easy. Started by pulling out refrigerator and unplugging it. Water valve for ice maker was already turned off due to leaking. Disconnected old valve, detached old valve, reattached new valve and reconnected water lines. Bled the lines and turned back on. Make sure temp in freezer stays at recommended temps for ice making.

Removed broken and installed nw part.

put in a new one

I needed one with the adapter. I installed it and there was ice in the tray the next morning...no problem

According to the online video instructions.

Turn off water, un-plug refrigerator, dis-connect water, un-screw bracket, remove valve and replace same way...Very easy

I watched the video and did the same thing on mine and now it is working fine

This would have been an easy repair, but I bought the Frig from Lowes and I think they added the icemaker. The replacement icemaker uint has a plug on it for easy replacement. My frig was hard wired so I had to cut off the plug and splice the wires. Not a real big deal but a small work space.

1-Unpluged the refrigerator 2- removed ice cube tray and some food( Placed in cooler )3- unscrewed the two screws holding the old unit lowering it and unplugged it. 4- Had to loosen the cooling coil to get to the pass through hole in the back and pulled the old wire out. Connected the wire adaptor to the old connectorand to the new ice maker. At this point I couldn`t pass the new plug through the back so I strapped it out of the way and installed the new ice maker using the two screws from the old one. Adjusted the fill adjustment and turned it on. Cubes in about 4 hours.

Took less than 10 min to install following the inclosed instructions. At first it was not making enough ice to make me happy so I set the temp. a little colder in freezer. Now making ice like crazy. Works better than the old one ever did. Very happy with the new replacement.

I followed the video that came with my email receipt but i had to use the extra electrical adapter, there is no where to put the extra wiring so it is hanging next to the wall. I was glad I didn't have to unplug the fridge. just kept the wire up so no water would come out. It took several hours to start working and it doesn't make as much ice as the old one, but at least it works. It was a very informative video. Thanks

moved freezer items to right of icemaker,loosen two nuts lifted icemaker over nuts,squeezed and pulled cable out turned over marked L bracket screw with marker for location plugged cable in tighten screws,made ice in 2 1/2 hours john

Unplug refrigerator power cord. Remove ice cube bin. Place wire signal arm in down (off) position. Ice Maker is held in place by two (slotted/hex headed) screws through keyhole slots over the top of Ice maker along the left side of freezer. Use mirror to locate screws then carefully loosen (do not remove) screws with a nut driver or screw driver. Lift Ice maker up and right until it releases from the screw heads. Unplug electrical connection. A flat screw driver may be required to loosen connector. Connect new unit electrical and Install new unit over screw heads and tighten screws. Replace Ice Bin and place wire signal arm in the up (on) position. Reconnect refrigerator power cord. After freezer cools down sufficiently it will start making ice.

Unplugged refrigerator. Removed control knob and cover. Unwired control and removed same. Removed plastic tube from old capillary tube and placed on new unit. Installed and wired in new unit, making sure new unit was in the "off" position. Plugged in refrigerator, turned control knob to the first numerical setting, and was rewarded with the startup of the refrigerator compressor. Voila!

Went well overall. I really thought that you guys taking the time to create a very helpful video was awesome. Thanks for doing that! The only difficulty I had was that my old ice maker had the connection toward the front, while the new one was in the back. So I had to use the adapter and had so much extra wiring to bundle, and tie wrap, with little place to go with it that I got frustrated. Wish I just had the correct replacement wire to begin with. Nonetheless, we are stocked with a full bin of ice after about 3-4 days.