2539338111 Kenmore Refrigerator - Instructions

Shut off water/power - pulled tray -loosened two screws holding ice maker - lifted it up and off - unhooked power connection installed new maker in reverse of above - power supply line was much to long but just pushed it under the ice tray ( away from the maker ) prior to ordering looked at comments from others regarding installation

I want to first say that before I ordered this part from "Part Select" I first went and talked with a local appliance repair shop. They quoted me a $120 charge to come out and check the problem. Then $30 and hour service fee, plus parts. He provided me a quote of about $250 for the job.
I found this part easily on the web site $77. It was very easy to instal. The only problem I had was the fact that in the side by side it was very difficult for me to get two hands inside the freezer to install it. (I have wide shoulders). Two screws loosened, no need to remove them. Just life the entire unit straight up. Unplug wire harness. Then just reverse order. Could not be easier. If you can change a light bulb you can do this.

Bought a new
capacitor.

I wrote down the Brand and model# of my refrigerator. googled it and PartSelect came up. I mean it literally took me 5 minutes to select the part, and order it! I ordered it on a Saturday and the part arrived on Tuesday! And it was a perfect fit! I will always return to PartSelect for any replacement parts for my appliances! Thank you!

I purchased the replacement part (no instructions sheet) from another company, not this one, that cost 2X's a much as this company. So I sent it back and ordered from this company. Got it faster then the post office sends us the stamps we order by internet and this ice maker had instructions.
Our's is a side by side refrig, so working space is limited but do-able. The old ice maker has made a clicking noise for years while trying to push the cubes out of the tray. They would get stuck and refreeze, sticking half way out of the tray.
I loosened the 2 screws with a socket driver (which are difficult to see), raised the unit up and off the screws. Unplugged the power & out it came. Removed the bracket on the side as instructed to attach to the new ice maker and in the trash the ol' ice maker went. Set the new ice maker on the screws, plugged in the power, tightened the screws and walla. A quiet ice maker. In fact, it would startle us the first day as we didn't hear the clicking noise indicating it was stuck. All of a sudden the cubes just dropped into the container. Alright! Don't know why I didn't do this years ago.

Removing the old unit was easy enough, just loosened two screws that attach unit to side of freezer and disconnected the wiring harness. But the new unit never goes in quite as easily because it's always just a little different from the original. In this case, the wiring ended up being about six inches longer and the excess had to be stuffed behind a shield at the rear of the unit. Theoretically, the wire could have been pushed back through the opening, but it got jammed and wouldn't go. I had to remove side rails and pry the shield forward in order to get the wiring back out of the way. The unit is a narrow side by side, so there wasn't a lot of room to move around. But it wasn't difficult, just tedious. I had to make sure the wiring did not come into contact with the heating element at the bottom of the icemaker. Once installed it worked great.

Followed the steps in the video on your site, really easy to do.

unplugged, removed old parts, replaced with new

This was a simple job. Raised the flap in the back that houses the compressor, removed the wire that holds the relay, pulled out the old relay and pushed the new one on. Replaced wire holder and that was it. Plugged it frig and freezer is at zero and lower compartment at 35. As easy as brushing your teeth!

I used a small screwdriver to disconnect wires from old starter. I connected the overload and starter, two wires. I put the unit back in the keeper, plugged the unit in, turned up the thermostat and it's working beautifully.

un plug fridge. removed ice maker from fridge. loosen 2 mounting screws. lift unit in slots to get over heads of screws. unplug wire harness. remove cover. remove 3 screws from control housing. remove 2 motor mounting screws. unplug motor wires from switches w/needle nose. installation is the reverse. plug in fridge turn on icemaker. takes 10 to 15 min to start to cycle.
easy and cheaper than new fridge or ice maker

I located the part that was the culprit as it had buzzed very much before quitting. This is an easy removal as the part is in a two prong jack and just needs to be carefully removed with the new part inserted back in the jack provided. The refrigerator works fine now, but the run capacitor will still buzz on start up of the compressor. I do hope this is normal in this model? anyway it runs fine mow. Thank you.

Door would not stay closed so I decided to replace the gasket... The new gasket install was easy and quick. I removed the liner and took off the old gasket, placed the new gasket on the liner and reinstalled the liner. However that did not fix the original issue of the door not closing. I followed all the instructions listed on the web site but none corrected the problem. The door on this model has no adjustment. So I adjusted the leveling wheels to tilt off center towards the back. That helped but still did not resolve the problem... I then closed the door slowly to see if it was being interfered with, As it turns out it was being hit by the bottom of the inside of the refrigerator. Since I could not adjust the door, I used the front leveling wheels to compensate for the lack of door adjustment. I slowly kept adjusting the w heels to see what effect it had. I finally adjusted them to the point were the door now closes and seals on its own. I’m guessing that over time the liner became malformed and caused the door to hit the inside of the refrigerator. After it started working I checked the level side to side and front to back. Side to side is good and there is a slight tilt to the rear.

took cover off inside freezer control . removed old fan and unpluged wire harness plugged new one up and fastened back in place and put control cover back on.

First, I unplugged the appliance. Safety, first.
Than I removed the shield which was held in by screws. This covered the fan, thermometer.
The defrost thermostat was taken out, with a little extra force. The wires on the defective part were no longer attached to the part. The instructions were easy to follow in replacing the defrost thermostat. I stripped the coating on the wire, attached it with the enclosed electical bugs. The assy was able to follow, and the part went back on. The refrigerator is working perfectly. I couldn't have done it without the help in diagnosing the problem and with the speedy delivery of the new part. Thanks for all your help and the ease of the installing the new part!