79571606015 Kenmore Refrigerator - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Calvin from Northome, MN
- Parts Used:
- 6600JB1010A
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Light quit coming on when door opened.
Unplug from wall receptacle. Pry switch out with screwdriver while pushing on inner tab. Then disconnect electrical plug.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Michael from TONAWANDA, NY
- Parts Used:
- 6600JB1010A
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
bad switch
The 2 minute or so video was not exactly matching the model that we had but the instructions were very good and important. The switch was a little difficult to get out from the side of the refrigerator.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- John from ELLWOOD CITY, PA
- Parts Used:
- MHY62044106
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
The original spring in the mullion door broke
I disconnected the refrigerator power, removed the 2 screws holding the mullion door on the left side of the refrigerator French-door (it’s the flap that allows the door to close). Removed the broken spring and installed the replacement spring in its place. Reinstalled the mullion door by putting it in place and installing the previously removed screws.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Donald from MERRITT IS, FL
- Parts Used:
- AGU75188619
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Old part did not seal properly
Read the reviews from other members and just did as they said. Needed a screw driver and the info from past persons review couldn’t have been easier.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Greg from CASA GRANDE, AZ
- Parts Used:
- 6600JB1010A
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers
door slight switch failed
Covered the sidewall with tape to protect. Pried the switch out with knife blade and removed electric plug with needle nose pliers. placed plug in new switch and pushed switch into the hole in the side wall. Took about five minutes.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Wayde from SEMINOLE, FL
- Parts Used:
- AGU75188619
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Spring broken in door mullion
Took 2 screws out and disconnect wire and install new part.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Lawrence from FALL RIVER, MA
- Parts Used:
- 4620JJ2009A
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Door Stopper had snapped off
Unscrewed what remained from broken door stop, aligned new one, screwed it in. Done!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Robert from WARREN, RI
- Parts Used:
- AGU75188619
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Spring in the plate front assembly broke. Door plate assembly would not move into correct position, preventing door from closing.
Followed Youtube video provided on the PartsSelect Website:
https://www.partselect.com/PS12374439-LG-AGU75188619-PLATE-ASSEMBLY-FRONT.htm?Inventory=12374439&SourceCode=20&SearchTerm=LFX28979ST
Made installation of the new part a piece of cake. Easy peasy!! Took less than 10 minutes.
https://www.partselect.com/PS12374439-LG-AGU75188619-PLATE-ASSEMBLY-FRONT.htm?Inventory=12374439&SourceCode=20&SearchTerm=LFX28979ST
Made installation of the new part a piece of cake. Easy peasy!! Took less than 10 minutes.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Sidney from ENDICOTT, NY
- Parts Used:
- 6600JB1010A
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
The switch became intermittent - Possibly a poor designe
Used a small screw driver inserted into the front of the switch (facing the front) and pried until the switch was coming out. When out, I removed the connect harness and replace the switch with a new one.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Charles from CURWENSVILLE, PA
- Parts Used:
- 6600JB1010A
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers, Screw drivers
Door light switch, 3rd one I have replaced in 6 years made in China.
Easy install, small screwdriver under back of old switch push out and pull out with small pliers. unsnap the old plug and install new. YOUR DONE
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Dean from HILLSDALE, MI
- Parts Used:
- 6600JB1010A
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Replace switch
Read previous tips
Taped off area around switch to protect surface
Used putty knife to extract switch
Used screwdriver to separate connector from switch
Plugged in connector
Pushed switch assembly into opening
Removed tape
Taped off area around switch to protect surface
Used putty knife to extract switch
Used screwdriver to separate connector from switch
Plugged in connector
Pushed switch assembly into opening
Removed tape
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Alma from Winterport, ME
- Parts Used:
- 6600JB1010A
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
the light did not work when door was opened. At first it would flicker then off completely.
My son just pried out the old switch with a screw driver snapped out the old one and snapped in the new one. Pretty sure even I could have done this. Very quick and easy. Thanks. :-)
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Karyn from DURHAM, NH
- Parts Used:
- 6600JB1010A
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Replace the light switch for the refrigerator
Cover the putty knife with tape so you do not scratch the side wall where the switch is located. Slide the knife under the edge of the switch and push in a bit towards the switch and slightly twist to pop the switch out of its hole. Disconnect the wires from the switch and simply plug in the new switch. Push wiring back into the hole and careful push the switch into the hole until it snaps into place.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- PAUL from AMARILLO, TX
- Parts Used:
- AGU75188619
- Difficulty Level:
- Very Difficult
- Total Repair Time:
- More than 2 hours
- Tools:
- Nutdriver
cannot get water to the icemaker
i changed the filter and was able to get water to the white coil at the bottom of the dispenser (left door) but could never get water to the icemalker.i also replaced the pump at the bottom of the door as well as the green ebr699172 dispenser electrical board.still can not get water to the icemaker.any help will be greatly appreciated.
paul
paul
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jasmin from SUNRISE, FL
- Parts Used:
- AJP73874601, AEC36702202, AEC36906401, AEC73877401, ACQ86549505
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
Unable to use the parts to hold my crisper i actually need drawers not pieces to install there is no where to install those pieces you sent me
Did not the crisper cover is ok the vegetable tray is ok but the pieces you sent to me no actually fit the crisper in is way off
Was this instruction helpful to you?
Thank you for voting!