2537034241G Kenmore Refrigerator - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Cindy from AMARILLO, TX
- Parts Used:
- 240597220
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
My fridge temp was warm. Freezer temp was ok, but fluctuated some.
I checked the dampener, it worked. The compressor and fan worked. I knew because my freezer was still hovering around 10 degrees. Coils were clean. Thermistor was the only thing it could be. Took all my shelves out. Removed four screws. Took the back panel off. The thermistor sits tucked in on the side. I piped it out, in clipped it. Used my multimeter to test the numbers. Numbers were off just a bit. Ordered the part. Crossed my fingers.,took less then 5 minutes to put the part in. Plugged in the fridge. It was sitting at 33 degrees in about an hour and a half. I can’t believe I fixed it. I knew NOTHING about refrigerators. For how big my fridge is, it would have cost 3,000 and up to get a new one with the same cu ft size. Instead, it cost me $44. That includes shipping. Thank you Parts Select!! Made it so easy to pick the correct part for my model fridge!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- hellen from SPRINGFIELD, MO
- Parts Used:
- 5304508016
- Difficulty Level:
- Very Difficult
- Total Repair Time:
- More than 2 hours
- Tools:
- Screw drivers
Roller screw recipients broke out. Can't be repaired.
Was not able to repair. Wasn't rollers I needed. Plastic screw recipients in front on frame had broken out so rollers weren't the problem. Tried gluing back pieces to no avail. Crisper frames are poorly designed.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- melvin from BASKING RIDGE, NJ
- Parts Used:
- EAFCBF
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
you r label (this end in arrow is wrong
placed filter in sideways
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Neville from LITHONIA, GA
- Parts Used:
- 242253002
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Wrench (Adjustable)
Not making ice in both ice maker or dispensing water
To confirm my diagnosis I first replace the filter still no water flow.
Check water supply from the wall valve: ok
Remove the entire inlet valve assembly and sit it over a small bucket.
Disconnect the tubing from the bottom of the 1st selenide valve: this is the one leading to the filter.
Place cup under water dispenser and activate dispenser. No water discharge from inlet valve confirm valve is bad.
Install the new valve matching the colored tubing with the color on each inlet valve.
Re-connect the water supply place container under water dispenser and activate: There will be a large gush of air then water. Dispense aprox 1 gallon of water to confirm all the air is purged from the system. Your refrigerator is now back to dispensing water and making ice.
Good luck everyone - Neville
Check water supply from the wall valve: ok
Remove the entire inlet valve assembly and sit it over a small bucket.
Disconnect the tubing from the bottom of the 1st selenide valve: this is the one leading to the filter.
Place cup under water dispenser and activate dispenser. No water discharge from inlet valve confirm valve is bad.
Install the new valve matching the colored tubing with the color on each inlet valve.
Re-connect the water supply place container under water dispenser and activate: There will be a large gush of air then water. Dispense aprox 1 gallon of water to confirm all the air is purged from the system. Your refrigerator is now back to dispensing water and making ice.
Good luck everyone - Neville
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Robert from CRANSTON, RI
- Parts Used:
- 5304508034, 5304508016
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
The left side roller broke away from the crisper cover frame
I removed and separated the crisper tray and cover from the refrigerator.
Removed the left side rail from the damaged cover and discarded the old cover.
I added the new roller to the new cover and replaced the side rail to the new cover and reassembled into the refrigerator
Removed the left side rail from the damaged cover and discarded the old cover.
I added the new roller to the new cover and replaced the side rail to the new cover and reassembled into the refrigerator
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Tim from SYLVANIA, OH
- Parts Used:
- 240597220
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
2 drawer undercounter beverage ref not getting cold enough. Wont get below 48°
Took drawers out by removing 2 screws on top of rail near front, then popped black plastic cover off in lower right inside cabinet...sensor just un plugged and new one plugged in easily...did not fix problem though...display set at 34 but bottom drawer reads about 40 at best and upper drawer reads around 55...dont think the 3 little fans inside on back wall have been running
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Laura from LANCASTER, CA
- Parts Used:
- 242253002
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver
No water to the ice maker or water tap.
Removed valve unplugged valve from electric removed water lines from valve and then reverse procedures then turn on water and use.That was it.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Gregory from POTTSTOWN, PA
- Parts Used:
- EAFCBF
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
NO PROBLEM JUST DECIDED IT WAS TIME TO CHANGE FILTER
VERY EASY SLIDE OLD ONE OUT AND PUT NEW ONE IT
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Richard from SEATTLE, WA
- Parts Used:
- 242009604
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Water filter would not disconnect from OEM Water Filter Base
Disconnect the two water supply tubes at the base of the Water Filter Base. Using a 7/16" open end wrench, press up on the blue "O" rings to disconnect the tubes. Use a Using an 8" long magnetic phillips head screw driver I was able to unscrew the 4 short screws holding the original water filter base and the immovable attached water filter. Replacement was easy. Simply slide the new base into the fixed slot on the refrigerator and reinstall the 4 holding screws. Reconnect the water supply tubes to the Water Filter Base. Install a new water filter.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Chuck from GRIFTON, NC
- Parts Used:
- 242220204
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Screw drivers
Water outlet tubing leaking in elbow behind water filter
Most difficult and time-consuming part of the job was clearing the refrigerator of food and shelving. Replaced tubing as it had split in the factory bend of the tubing directly behind the water filter. Take your time and don't get in a hurry.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Joshua from AKRON, OH
- Parts Used:
- 809069206
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers, Socket set
condenser fan is no longer holding running speed
Removed the baskets/containers from freezer compartment. Removed back panel from the freezer interior.
Swapped the fan on the mount
Tested and reassembled fully
Back in working order
Full steps followed
https://www.youtube.com/watch?v=73rubWwQork
Swapped the fan on the mount
Tested and reassembled fully
Back in working order
Full steps followed
https://www.youtube.com/watch?v=73rubWwQork
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- James from ELK GROVE, CA
- Parts Used:
- 242009604
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers, Socket set
New off brand water filter could not be removed from the water filter base
Removed the water lines from the old base. Installed new base and reconnected water lines. Installed new filter.Turned on the water line behind the refrigerator. Opened Refrigerator door to watch for leaks. No Leakes. The new filter base was
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- ELIZABETH from HENRICO, VA
- Parts Used:
- 242010901
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
Wrong Part sent!!!!!
I did not do a repair. You sent the wrong part & I didn't open the package but I can't get hold of anyone to return the part and get the correct part.
I am very upset that no one will help me. I paid $ 37.28 for the part I ordered and then the wrong part was sent
The sku # on the package is 242010901.This is a roller type part and I ordered a small wheel.
I can't even find a return address to send it to.. Please help me
Elizabeth Romage
libbieinrichmond@comcast.net
8042627963
I am very upset that no one will help me. I paid $ 37.28 for the part I ordered and then the wrong part was sent
The sku # on the package is 242010901.This is a roller type part and I ordered a small wheel.
I can't even find a return address to send it to.. Please help me
Elizabeth Romage
libbieinrichmond@comcast.net
8042627963
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- fred from Austin, TX
- Parts Used:
- EAFCBF
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
routine maintenance
slide old filter out and insert new one
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Edward D from YOUNGSTOWN, OH
- Parts Used:
- 5304508033, 5304508016
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
roller broke off
remove drawer , remove top shelve remove and repleace side rails ond take rollers off and repleace rollers. not bad at all
Was this instruction helpful to you?
Thank you for voting!