59673003511 Kenmore Refrigerator - Instructions

Super simple job. Unplug freezer. Have a hair dryer handy to defrost while you have unit open. Remove food from the bottom two shelves and floor of freezer. Remove mid plastic cover removing three screws. (All screws are same so mixing them is no big deal.) Use drill-driver or screw driver to spin out six screws on lower back plate. Remove plate. Thermistor is on left side of the cooling tubing. Use hair dryer to melt ice if necessary. Un-clip thermistor power connection, and unsnap it from tubing. snap new thermistor on cooling tube and hook up wiring. Ensure plug fits together correctly and snugly. If heavy icing exists, use hair dryer to melt ice on coils and through fan. Ensure water drains out of drain pan under coils. Wipe up as much ice melt as possible to prvent re-frosting upon start-up. Replace lower panel and six screws. Replace mid-panel cover and three screws and replace shelves. Done! Plug freezer back in and expect 30 second delay before unit will start up.

Watched video. Unplugged refrigerator and popped out switch. In plugged connector and pushed switch in place. Plugged in refrigerator and the light worked

The broken tracks popped off with a little effort, and the new tracks snapped in place. No tools required, except a screw driver helped to pop the broken tracks out, and snap the new ones in place.

This is an incredibly easy repair.

1) Remove the three screws holding the old icemaker

2) Disconnect the electrical connection (I used a spoon to get in and undo the connector clip

Do the opposite to install the new icemaker.

Total elapsed time was about 5 minutes.

Removed the 2 screws holding the light bulb shield, then the 4 uolding the metal panel. Unplugged the olw door switch and replaced.
reassembled the pieces.

Followed online instructions. UnPlug and Plug in new part

Took the old one out and plug the new one in, simply as 1 2 3. Order the part one morning,it was here the next afternoon, the ice maker was fixed in less than a half hour. we will order from you the next time.

take out Ice maker tray, remove three screws holding the ice maker, unplug electrical connector. Replace with new Ice maker,Ice started to fill the tray. ENJOY!!
THANKS.

It was not complicated but it took more squeezing and reaching into the narrow space than actually removing three screws and unplugging the electrical harness. But that was all that was necessary, to install, three screws held the unit in place and re-connect the electrical harness. It saved me about $100 in labor and the inconvenience of scheduling a service call and waiting for a week or so. The best part was that I ordered the unit on line on Tuesday eveining and it was at my home by Friday afternoon with no extra shipping charges. Great service!.

Removed the door, removed the tray, removed the back bar(slipped the female cover off 1 side), removed the left slide, installed the new slide, installed the back bar, slipped in the drawer, popped the anchor back in the door with glue, installed the door and POW, it's done.

This was a snap. Loosened 3 screws, removed
old ice maker. Made cutout for water chute. Plugged in
wiring harness plug. Installed new ice maker. Tightened 3 screws.

These brain surgeons that charge $80.00 just to show up at my house to repair an appliance are history.

Replaced inlet valve.

Referencing the info/schematics you have on your website, I unscrewed/unattached top-front panel (carefully), from behind the panel you have to detach the wires (2) from the switch, pushed "in" the switch to remove, put in new switch and attach wires to test BEFORE remounting panel. Tada!! Thank you PartSelect! You saved me at least $80...would have been at least $100 to have a repair person come to the house!

I determined that the ice cube maker was no longer heating the cubes so they could be released into the ice tray. After ordering a new unit, taking out four screws and disconnecting the quick disconnect of wires I plugged the new one in and we were back in business.

Unplug power to refridg/freezer. Removed the screw in rt. rear bottom of ice maker to remove. After removing slightly, unplug pigtail. Remove ice maker completely. Remove large square cover from left side to expose motor. Remove screws to remove motor. Replce with new. Replace ice maker to freezer, plug pigtail back in, put screw back in rt rear bottom, plug refridg/freezer back into power source. Ice was making in about 2 1/2 hours.