79578503802 Kenmore Refrigerator - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Awilda from Staten Island, NY
- Parts Used:
- MJU62070602
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
The water line was leaking
Removed the damaged tube and replaced the it with a new one.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Thomas from Orlando, FL
- Parts Used:
- MJX41178908
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers, Wrench set
Pump for ice maker leaked.
Easy repair. Unplugged refer. Took back cover off with screwdriver. Unscrewed the support for the pump. Unhooked water lines from both ends of bad pump. Pulled electrical line off the old pump. Put the support on the new pump, hooked up lines, and electrical plug and screwed the pump to the frame. Put the coever back on unit. Plugged back into wall. Worked immediately.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jack from Ellenton, FL
- Parts Used:
- 6600JB1010A
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
light out
slid screw driver under edge of switch, easy.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- GREG from STILLWATER, NJ
- Parts Used:
- 4930JA3091A
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Wrench (Adjustable)
plastic tube leaking at connector
Uncoupled the old connector, replaced with new connector and attached supply line. Repair easy with right part, prior to ordering the right part I had tried a compression fitting and it still leaked. U-tube and others demonstrating repair assured me I was on the right path.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Teresa from Miami, FL
- Parts Used:
- 4004JA3002A
- Difficulty Level:
- Really Easy
- Total Repair Time:
- More than 2 hours
Frost in the freezer. Icemaker frozen.
I called LG and followed the instructions given over the phone. The instructions couldn't have been simpler. Disconnect the appliance for several hours and then connect again. I disconnected the appliance overnight, cleaned out the freezer, and reconnected it. Problem solved. Did not need to call a repairman and did not use the clips.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Cedric from Milwaukee, WI
- Parts Used:
- AAP73871501
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
broken door
Simple replacement part.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Virginia from Raleigh, NC
- Parts Used:
- 4975JA2028A
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Guide assembly rails
Very easy just took old out and put in the new ones. Took less then 2 min.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- nicholas from Southampton, PA
- Parts Used:
- 3016JA2004E
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
cracked funnel installing ice door relay
clipped new part on ice door
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Bard from Alpine, CA
- Parts Used:
- AAP33726606
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
No problem
It's a snap in part. 10 seconds to install
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- William from Bridge City, TX
- Parts Used:
- AEQ36756901
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
icemaker quit working
My husband took out the ice maker. We ordered the part. He looked on YouTube for instructions. Including looking up instructions, I think it took him way less than an hour.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Sarah from Elk Grove, CA
- Parts Used:
- 4932JA3002A
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers
Each time we've had to move we have to remove the doors from the fridge to get it thru the front door.since water and ice run thru the freezer door there are 2 tubes that connect at the bottom of the freezer door that aren't meant to be separated very often if ever.it's easier to cut the tubing on b
With alot of elbow grease and a pair of pliars we managed to get the old connector off wo cuttig the tubing as the tubing was getting to short from being cut once to many times & there was no more play in the length.Original connector was a different color and shapped slightly different than the new one so was a bit concerned that I had ordered the wrong part but it went one very easily & did not leak. We even managed to remove it again just to see if it was possible wo cutting again. it came off with no trouble.I would say the replacement part was a better fit than the original simply because we could remove it easily wo having to cut the tube!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Thomas from Bay Shore, NY
- Parts Used:
- EAG62831801
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Interior Light Would Not Turn Off
Tape off the light button so door alarm does not go off. Take off the clear light shield and remove the light bulbs. Be careful, bulbs may still be HOT!! With Phillips head screw driver unscrew the light plate assy. Drop it down in a comfortable position. Disconnect the connector, unscrew the thermal sensor and remove light assy. Install new light assy into light plate assy. There is no thermal senor in the new assy. Snap light plate assy back into place and install the two screws previously taken out. Install bulbs and clear cover. Remove tape from light door switches and you are done. Lights should go on and off when door buttons are pushed in and out.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Brian from Fairmont, WV
- Parts Used:
- 4975JA2028A
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Broken Drawer Slide Rails
Be sure to order two if both are broken. The picture shows two but only comes as a single item. Super easy to replace.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Reginald A. Green from Pelham, AL
- Parts Used:
- 4430JJ2004B, 4430JJ2004A
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Plastic door latch/ cam shaft broke on left side door
Removed white plastic trim and installed new latch / cam shaft
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Donna from Abilene, TX
- Parts Used:
- 3550JJ1070B, 3110JJ1014A
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Lamp cover and case had melted
I removed the old lamp cover and case. Discovered that the last repair person had not re installed it correctly so the case had melted from the bulbs. I Removed the screws that was supposed to hold it up, assembled the case and cover, inserted the screws and anchored them in where they belong. Problem solved!
Was this instruction helpful to you?
Thank you for voting!