79572063117 Kenmore Refrigerator - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Vispi from SUGAR LAND, TX
- Parts Used:
- ADX72930461, ADX72930460
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
The door gaskets had become hard and curled up - would not seal properly
Watch YouTube videos on this topic if you are uncertain before tackling the job. The right door was easy to replace. Just pull the gasket with your fingers and it will come off easily. Place new gasket over door and use fingers to press it inside the groove few inches at a time. Pay attention to gasket orientation.
The left door is a bit harder because you need to remove the mullion at the door edge using a screw driver. Remove two screws on the center hinge and then slide the mullion up to disengage. Then unplug the wires to remove the mullion. Replace the gasket as described above and replace the mullion reversing the directions shown above.
Could not believe how easy it was!
The left door is a bit harder because you need to remove the mullion at the door edge using a screw driver. Remove two screws on the center hinge and then slide the mullion up to disengage. Then unplug the wires to remove the mullion. Replace the gasket as described above and replace the mullion reversing the directions shown above.
Could not believe how easy it was!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Thomas from LA PLACE, LA
- Parts Used:
- AEQ73110203
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
Ice maker wore out.
I installed the new 3 wire ice maker very easily, but it was defective. I was told that instructions for the return of the defective part would be sent later due to the virus. I have never received the return instruction.
I did receive a credit for the defective part. VERY Satisfied with y’all’s service.
Waiting for return instructions if y’all still want it back.
Thanks,
Thomas Pennebaker
I did receive a credit for the defective part. VERY Satisfied with y’all’s service.
Waiting for return instructions if y’all still want it back.
Thanks,
Thomas Pennebaker
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Daniel from MCMURRAY, PA
- Parts Used:
- ADX72930461
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Pliers
Gasket on one of the side opening doors was torn and no longer a tight seal.
Fortunately, others had left comments about this installation, so proved very helpful. First thing was laying out the gasket flag on the counter to allow it to unbend, get out the kinks from shipping. While the new gasket was laying out on the counter, started removing the old gasket. As it had been there for 11 years, needed pliers to get a corner started. I was slow and careful removing the old gasket in case I needed to put it back in. A very helpful suggestion from others was to lightly rub dishwashing soap on the gasket edge that fits in the groove in the door. Again, slow and careful, got it installed, wiped off any excess dishwashing liquid, and the door closed with a better seal in a long time. Pleasantly surprised how easy this was to do!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jane from SHORELINE, WA
- Parts Used:
- 6600JB1010A
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Door switch would not turn on interior refrigerator light.
I had previously watched a YouTube video (do this first!!) on a similar Kenmore model so I knew what to look out for: (1) turned off power, (2) took thin putty knife to slip under outer lip of switch (most screwdrivers are too thick), (3) wiggled switch at front end to release the tab, (4) unplugged from the socket, (5) plugged in new switch, (6) popped new switch back into door, (7) turned on power. Voila !! Super easy. I couldn't believe it.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Thomas from CHULA VISTA, CA
- Parts Used:
- ADX72930460
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Left side gasket was torn and would seal properly
Took off the French door Mullen by unscrewing middle area. Unconnected the wires for the door sensor. Then detached old gasket and replaced with new gasket. Reattached the wiring and snapped Mullen flap in place and finally rescrewed to the door. Seal is very good now.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- David from PENNSVILLE, NJ
- Parts Used:
- 6600JB1010A
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers, Screw drivers
Switch stops working
Replace with new switch. this is the third switch i have replaced in 10 years. the only part, besides a light bulb, that has gone bad. obviously this is a problem with this model for Kenmore, or just poor switch design.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Maryann from BROOKFIELD, IL
- Parts Used:
- MDS38201426
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Icing up in the freezer due to poor gasket
Watched a couple of YouTube videos and then went at it
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Craig from SPRING HILL, FL
- Parts Used:
- MDS38201426
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Ice crystals appearing on the face of the freezer draws
Part Select had a great video which made the repair easy, using a putty knife to start removing the freeze door gasket. Once removed the install is simple just snap the new gasket into the track, but start at the corner. Other company's have a video requiring you to remove the entire freezer compartment out of the appliance, unnecessary waste of time and labor.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- William L from SUMAS, WA
- Parts Used:
- 6600JB1010A
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
light didn't come on when the door was opened
I took a very thin bladed screwdriver and took the old part out -carefully.
The new part fit in quite easily.
The new part fit in quite easily.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- shirley from ONALASKA, WI
- Parts Used:
- 6600JB1010A
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
Light switch for refrigerator not functioning
Followed instructions online
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Joseph from SAINT LOUIS, MO
- Parts Used:
- AEQ73110203
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Pliers, Screw drivers
The Ice maker stopped working
Thanks to videos on You-Tube which showed step by step removal and replacement. It was a simple process. only thing missing on the video was information on the green ground wire.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Cheryl from Ormond Beach, FL
- Parts Used:
- MDS38201426
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
Freezer door gasket formed gaps between door and refrigerator.
Removed old gasket from the door and replaced with new gasket.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- William from LARGO, FL
- Parts Used:
- AAP73252302
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Broken door basket
The repair was an easy replacement. The problem was the LG part was no longer available from LG or any of the other places I tried. The PartSelect customer service representative was a true professional and did an outstanding job of helping find the correct part (LG's diagram was unreadable) and cross-referenced it to find the the part that PartSelect actually had in stock. I had the part in four day. The best customer service I have had in years. I lost his name but the order was 13449146. He deserves a raise!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Sidney from ENDICOTT, NY
- Parts Used:
- 6600JB1010A
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
The switch became intermittent - Possibly a poor designe
Used a small screw driver inserted into the front of the switch (facing the front) and pried until the switch was coming out. When out, I removed the connect harness and replace the switch with a new one.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Michael from TONAWANDA, NY
- Parts Used:
- 6600JB1010A
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
bad switch
The 2 minute or so video was not exactly matching the model that we had but the instructions were very good and important. The switch was a little difficult to get out from the side of the refrigerator.
Was this instruction helpful to you?
Thank you for voting!