79572495611 Kenmore Refrigerator - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- David from BRAINERD, MN
- Parts Used:
- ADX73550624
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers
door gasket was broken
started in a corner of the door and pulled out the old gasket and inserted the new gasket by being sure to start each corner before pushing in the center so it fits good first. extremely easy.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Janice from PINCKNEY, MI
- Parts Used:
- ADX73550624
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Gasket split
Took the old gasket out, put the new one in
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- MIKE from MENASHA, WI
- Parts Used:
- ADX73550624
- Difficulty Level:
- Very Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers
After 10 years of service the right door gasket needed replacement.
It was SO easy. No clamps or brackets. Grabbed the gasket with pliers to get started removing it - just pull it out of the deep groove inset around the perimeter of the door. Within one minute I had the old gasket removed. Started installing the new gasket by inserting the top right corner 1st (pushing the new gasket profile into the deep groove inset on the door). Working around the top and right side slowly inserting the gasket profile into the deep groove around the entire door. You may have to "adjust" a bit by pulling on the gasket but within 5 minutes I had the new gasket in-place never having to turn off the refrigerator. YouTube has great "how-to" videos. It's easy!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Andre from VIRGINIA BCH, VA
- Parts Used:
- ADX73550624
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Torn door seal
Pull out old seal with hands. Install new seal into channel by pushing seal into channel with you fingers.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Patrick from AUGUSTA, WV
- Parts Used:
- AGU75188619
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Spring on door Mullion broke
Watched a YouTube video on how to replace the door flipper (mullion). Very easy to unscrew the plate and disconnect the electrical circuit. Then gently slide up the flipper and replace with a new one.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- George from PARIS, TX
- Parts Used:
- AKC73249309
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Ice maker bucket/dispenser broke
Removed old bucket and placed new one In its place. New one is actually better than OEM part because it has an arm than breaks up any ice that may jam.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Michael from SALINAS, CA
- Parts Used:
- ADX73550624
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Door gasket tore.
With a small flat blade screw driver, gently pry the corner of the gasket from the door.
Pull it loose across the top, then down the sides.
Wipe the gasket track clean with a damp cloth.
Start installing the new gasket at one of the top corners. Then the other top corner. Press the gasket into the track between the top corners.
Next do the bottom corners. Pressing the bottom between the corners.
Then press in each side.
Elapsed time: 3-5 minutes.
Pull it loose across the top, then down the sides.
Wipe the gasket track clean with a damp cloth.
Start installing the new gasket at one of the top corners. Then the other top corner. Press the gasket into the track between the top corners.
Next do the bottom corners. Pressing the bottom between the corners.
Then press in each side.
Elapsed time: 3-5 minutes.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- BG from WEATHERFORD, TX
- Parts Used:
- MHY62044106
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers
I actually took a picture of the correct spring installation at a big box store that carried LG. I had called LG, but they said they didn't have any installation brochures, and to call a registered LG repairman. That was out of the question, since the repairman would charge $100 just to show up.
I looked at the picture I took. Used needle nose pliers and inserted one end. Unless the lady of the house is very strong, this should be handled by a man, because of the rigid spring. Once the spring was inserted into one side of the flap, I used the pliers to get the other end into the proper slot. Very easy, but the spring is very strong !!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Scott from MORGAN, TX
- Parts Used:
- AEQ73110210
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
ice would stick in 5 of the 14 cubes spaces from mineral deposits, then ice couldn't drop and water would not fill
was easy watching youtube video of how to replace whole ice maker, was only 3 screws, remove from the door, a couple of screws hold it to the flat piece, route the wires around the unit, connect the plug as installing it in the door, position it, and tighten 3 screws, that easy
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Dave from CORDOVA, TN
- Parts Used:
- AAP73631702
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Old assembly had broken clear plastic.
Simply lifted old part up, removed. Took new part put in place and pushed downward as it firmly locked in place. Less than 1 min.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- MJ from LAGUNA HILLS, CA
- Parts Used:
- AAP73631702
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Broken left sided attachment clasp/arm
The replacement basket for the left swing door went extremely smooth. The part was an exact fit and just required a little pressure while attaching the new replacement part.
highly recommend part select in doing a replacement for this part.
The schematic for the refrigerator is blurry and difficult to see on-line, so one a representative from parts select assisted me in finding the correct part.
two thumbs up!
highly recommend part select in doing a replacement for this part.
The schematic for the refrigerator is blurry and difficult to see on-line, so one a representative from parts select assisted me in finding the correct part.
two thumbs up!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Daniel from ABERDEEN, WA
- Parts Used:
- AJU72992601
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Screw drivers, Wrench set
Low water pressure which in turn led to no water and no ice.
Unplugged fridge, shut off water supply disconnected water supply from fridge. Remove screws that hold lower cover on back of fridge, removed screws holding valve assembly to fridge. Disconnect two electrical connections, remove black c-clip on out flow water line, lift fitting on outflow line side and pull water line off. Replace with valve assembly in reverse order
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jim from WELLINGTON, FL
- Parts Used:
- AGU75188619
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Plate Assembly Spring Broken
Remove 2 screws holding to door. Slide assembly up. Unplug connector. Remove old Plate Assembly. Do reverse to reinstall. Plug connector. Push in wires. Slide plate on. Fasten screws. Done
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Thomas from Wendell, NC
- Parts Used:
- ADX73550621, ADX73550624
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
Dampness on gaskets, mold and mildew
on left side door, I had to remove the flapper (the piece that rotates when you close the door to allow right door to seal. very simple, remove the flapper hingelift up to get the flapper off the door and move it out of the way.
Remove both door gaskets by pulling them out with your hands. Not the orientation of the gaskets because you will have to install the new gaksets in the same orientation.
Press the new gasket in place, into the slot that goes around the inside of the door, by using two fingers to press it into place. Cntinue this all around then go back and press again to assure the gasket is fully seated.
In my case, replacing the gaskets did not solve the issue, but they needed to be replaced do to the condition. The moisture issue was resolve by replacing the flapper (mentioned above)
Remove both door gaskets by pulling them out with your hands. Not the orientation of the gaskets because you will have to install the new gaksets in the same orientation.
Press the new gasket in place, into the slot that goes around the inside of the door, by using two fingers to press it into place. Cntinue this all around then go back and press again to assure the gasket is fully seated.
In my case, replacing the gaskets did not solve the issue, but they needed to be replaced do to the condition. The moisture issue was resolve by replacing the flapper (mentioned above)
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- William from VICKSBURG, MS
- Parts Used:
- MHY62044106
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
The Mullion Strip Spring Broke
Removed mullion strip with Phillips screwdriver replaced spring reinstalled the mullion strip all in about 15 minutes.
Was this instruction helpful to you?
Thank you for voting!