79571609014 Kenmore Refrigerator - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- David from PENNSVILLE, NJ
- Parts Used:
- 6600JB1010A
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers, Screw drivers
Switch stops working
Replace with new switch. this is the third switch i have replaced in 10 years. the only part, besides a light bulb, that has gone bad. obviously this is a problem with this model for Kenmore, or just poor switch design.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Greg from CASA GRANDE, AZ
- Parts Used:
- 6600JB1010A
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers
door slight switch failed
Covered the sidewall with tape to protect. Pried the switch out with knife blade and removed electric plug with needle nose pliers. placed plug in new switch and pushed switch into the hole in the side wall. Took about five minutes.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Charles from CURWENSVILLE, PA
- Parts Used:
- 6600JB1010A
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers, Screw drivers
Door light switch, 3rd one I have replaced in 6 years made in China.
Easy install, small screwdriver under back of old switch push out and pull out with small pliers. unsnap the old plug and install new. YOUR DONE
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Dean from HILLSDALE, MI
- Parts Used:
- 6600JB1010A
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Replace switch
Read previous tips
Taped off area around switch to protect surface
Used putty knife to extract switch
Used screwdriver to separate connector from switch
Plugged in connector
Pushed switch assembly into opening
Removed tape
Taped off area around switch to protect surface
Used putty knife to extract switch
Used screwdriver to separate connector from switch
Plugged in connector
Pushed switch assembly into opening
Removed tape
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Alma from Winterport, ME
- Parts Used:
- 6600JB1010A
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
the light did not work when door was opened. At first it would flicker then off completely.
My son just pried out the old switch with a screw driver snapped out the old one and snapped in the new one. Pretty sure even I could have done this. Very quick and easy. Thanks. :-)
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Karyn from DURHAM, NH
- Parts Used:
- 6600JB1010A
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Replace the light switch for the refrigerator
Cover the putty knife with tape so you do not scratch the side wall where the switch is located. Slide the knife under the edge of the switch and push in a bit towards the switch and slightly twist to pop the switch out of its hole. Disconnect the wires from the switch and simply plug in the new switch. Push wiring back into the hole and careful push the switch into the hole until it snaps into place.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jasmin from SUNRISE, FL
- Parts Used:
- AJP73874601, AEC36702202, AEC36906401, AEC73877401, ACQ86549505
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
Unable to use the parts to hold my crisper i actually need drawers not pieces to install there is no where to install those pieces you sent me
Did not the crisper cover is ok the vegetable tray is ok but the pieces you sent to me no actually fit the crisper in is way off
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Tammy from HAGERSTOWN, MD
- Parts Used:
- 6600JB1010A
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Refrigerator light had a short in it and would randomly work
Unplugged the fridge. Used a screwdriver to loosen the switch. Easy to disconnect from fridge and just plugged the new switch in. Popped right back into the side of the fridge and worked perfectly.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jack from Ellenton, FL
- Parts Used:
- 6600JB1010A
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
light out
slid screw driver under edge of switch, easy.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Paul from San Jose, CA
- Parts Used:
- 6600JB1010A
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers
Unit kept beeping as if the freezer door was open
I popped the old switch out of place and then disconnected the wire harness from the switch with a pair of needle nose pliers. I then inserted the harness into the new switch and popped the switch into place. Super easy and fast.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- dorothy from SALISBURY, MD
- Parts Used:
- MJB63190001
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
replace hand screw
unfortunately my fridge stopped working. I purchased another but wanted to try and repair the old one. when ew one arrived, the old one was supposed to be put in garage but instead was hauled away. Had delivery return next day but they had as already removed and lost the handle screw for the bottom freezer and the screw that holds handle in place. ordered the handle screw and picked up the nut. very simple to install the screw and put handle back on.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Pat from West Bend, WI
- Parts Used:
- MDS64172918
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
The gasket on our bottom drawer freezer was torn
Simply used a flat head screwdriver to get the first few inches of the gasket out of its track and after that just pulled it by hand. New gasket slipped over the door, lined up the corner and pressed into in the track. Checked to see that it was snug all over and we were done. 5 minutes at the very most. Never would have noticed this. Took all the bins out of the freezer to give it a good cleaning and noticed the torn piece hanging. Our refrigerator runs much less often. Expect to see a difference in our electric bill!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Cedric from Milwaukee, WI
- Parts Used:
- AAP73871501
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
broken door
Simple replacement part.
Was this instruction helpful to you?
Thank you for voting!