3639517910 Kenmore Refrigerator - Instructions

Removed the ice maker from the freezer. Removed the switch. Tested the switch with a multimeter. Ordered a new switch. Replaced it in the box. Installed the ice maker ( 3screws and electric cord plug. It works. Details available on the internet.

I removed the maker from the freezer, three phillps head screws, I pulled off the white plastic cover and found the top (small) gear had poped out, after carefull inspection, I notice two missing teeth. I ordered a new gear from ParstSelect re-installed and with in two days my ice maker was working like new. I estimate I saved myself seveal hundred dollars, my wife wanted to call a service professional or worse buy a new refrigerator freezer. Thanks PartSelect!

removed old parts and installed new. went smooth

I placed the new part on the end of the freezer door guard and firmly pushed it in until it 'clicked'. Easy as pie! The more difficult part was to remove the broken off part inside the opening of the freezer door hwere the new bar end was to be inserted. I finally used thin nose pliers to reach in and grab the broken off part.

Disassembled front door/cover (3 screws), then removed deflection door assy, (4 1/4" nuts), CArefully and methodically removed C Clip and grinder teeth...Be careful with this step to document/remeber how to re-assemble! Auger repleced then reverse steps...
All in all, not too bad, but you can easily screw up the teeth re-assembly.

Ordered the icemaker replacement. unplugged the unit, followed the simple instructions and got it done in less than 30 minutes. It did take a LONG time to start making ice. But it's working now.

I ordered the wrong part, the ice maker assembly, because your diagram was not marked properly. I returned the part and you credited my account. Thanks. Ordered the new bucket. It worked fine. Now I have ice and crushed Ice whenever I want. Thanks.

p.s. I didnt use any tools, but to satisfy you I select nut driver.

Found broken pieces of deflector in delivered ice. Removed dispenser, carefully disassembled it, marking fasteners, sprimgs, and levers. Local repaimen say no replacement part available, must replace entire ice maker @ $350. Found exact part in your online reference, ordered at price of $3.76, part arrived two days later--perfect fit, exactly same as original. Reassembled, and it works exactly like new. Family very happy. Good job!!!!!

Was concerned that new icemaker was quite a bit different than the one we were replacing. Called GE to confirm it was correct.

Went ahead and installed the unit, using the supplied electric cable adapter.

A little difficult to deal with the extra cable, but everything worked OK and it's making ice normally.

I pulled the refrigerator away from the wall and turned off the water to the refrigerator and unplugged it from the wall. After removing the icebucket from the freezer I located the mounting screws, loosened them, unplugged the electrical connection below the icemaker and carefully removed it from the freezer. I unpacked the replacement icemaker, matched it against the original and attached the electrical connection adapter. Using the slots provided on the new icemaker I placed it over the mounting screws after aligning the water inlet pipe properly. I tightened the mounting screws while maintaining the icemaker in a level position. I plugged in the electrical connector. Then I replaced the icebucket, plugged in the refigerator back into the 110VAC outlet, turned on the water and repositioned the refrigerator in it's normal position.

I removed the 4 screws from the cover and replaced the auger and ice bucket assembly. Extremely simple and I was amazed how easy it was.

Removed the face plate (4 screws) on the ice bucket/auger and put it on the new unit.

Performed self test.turned off ice maker switch four 5 minutes.Then turn on switch,within 10 seconds,pushed ice paddle 3 times,with 1 second in between each push.Push all the way back and release. Ice maker should cycle and squirt water. My ice maker did neither.I unplugged cord from fridge.So i replaced the ice maker.After a couple of screws had ice again !

it was really easy now it works like it did when it was brand new

Took unit apart but did not take photos of how to put unit back together, so needless to say it took longer then it should have. My error. Ordering the part was very easy and within days the part arrived at my door. Should the need arise, I would order again from Part Select.com.