25370347411 Kenmore Refrigerator - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Edward D from YOUNGSTOWN, OH
- Parts Used:
- 5304508033, 5304508016
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
roller broke off
remove drawer , remove top shelve remove and repleace side rails ond take rollers off and repleace rollers. not bad at all
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- fred from Austin, TX
- Parts Used:
- EAFCBF
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
routine maintenance
slide old filter out and insert new one
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Dennis from OLATHE, KS
- Parts Used:
- 242009604
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Screw drivers, Wrench (Adjustable)
Filter wouldn't engage
Basically unhooked water lines and removed the screws
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Dean from Pawleys island, SC
- Parts Used:
- 242253002
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Wrench (Adjustable)
Refrigerator water dusoeswr stopped working
I removed the defective water valve. All wiring and tubing connectios were color coded.
It connected the water tubes and electric plugs to new water valve.
The water dispenser worked perfectly after I reconnected everything.
It connected the water tubes and electric plugs to new water valve.
The water dispenser worked perfectly after I reconnected everything.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Daune from OCALA, FL
- Parts Used:
- 241675704
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 1- 2 hours
- Tools:
- Screw drivers
Ice Maker was making ice erratically
After sending PartSelect the info to their troubleshooting dept. about my ice maker, they recommended replacing the ice solenoid. I did so at a cost of $102. No change, turned out replacing the ice maker(did not purchase from PartsSelect) was the issue and works fine now.
So wasted $102. FYI the part took 6 days to arrive.
So wasted $102. FYI the part took 6 days to arrive.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Michael from FREE SOIL, MI
- Parts Used:
- 243297613
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers, Socket set
Original ice maker not working leaking water water out door
Removed exterior housing, sliding old unit forward to release. New unit went in easily. Caution wires don't get pinched.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Robert from Lexington, SC
- Parts Used:
- 5304537408
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 1- 2 hours
THE GASKET LOCKING INSERT DID NOT FIT THE BOTTOM OF THE DOOR.
I REMOVED THE OLD GASKET BEING VERY CAREFUL TO SEE EXACTLY HOW IT CAME OFF. I INSERTED THE LOCKING INSERT INTO THE TRACK IN THE DOOR WHICH DID NOT FIT AS THE OLD ONE DID. AFTER USING TREMENDOUS FORCE WITH MULTIPLE TOOLS I DID MANAGE TO GET THE TOP AND THE SIDES TO LOCK INTO PLACE AND EVENTUALLY HOLD. THE BOTTOM OF THE GASKET DID NOT HOLD SO I USED CLEAR CAULK AND TAPE TO HOLD THE GASKET IN UNTIL THE CAULK CURED. AFTER THE CAULK CURED THE GASKET HAS, SO FAR, REMAINED TIGHT.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- James from ORLANDO, FL
- Parts Used:
- 241829001
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 30 - 60 mins
ICE WOULDN'T DISPENSE FROM ICE BOX
I read other suggestions trying isolate auger motor shaft with pliers while turning bar drive. needle nose pliers could hold the shaft. bar drive just would spin. so took the whole ice box assembly out
(only 2 screws) and with a metal cutting blade used the sawzall to cut along the shaft. freed it up enough to then unscrew it from that point. Left handed threads by the way.
(only 2 screws) and with a metal cutting blade used the sawzall to cut along the shaft. freed it up enough to then unscrew it from that point. Left handed threads by the way.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Bernard from NEW WINDSOR, NY
- Parts Used:
- 241779401
- Difficulty Level:
- Very Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
1 Broken plastic mullion hinge. Mullion was not operating correctly.
Removed screw on Mullion so that the replacement hinge can slide onto the small plastic bracket on the door. Slid the mullion on the hinges and screwed in muliion (1 screw).
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Lorraine from Arlington, VA
- Parts Used:
- 242161202
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
very Simple!
Insert the bottom part of the trim first, then pull up to snap on the top. PartSelect.com is a fantastic website!!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- EDWIN from ELWOOD, IN
- Parts Used:
- 5308000010
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver
loud noise fan blade broke,off balance
take 1/4 hex screws out clean out dust ,remove old fan blade replace with new install bolts .
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Greg from henrico, VA
- Parts Used:
- 241639502
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 1- 2 hours
- Tools:
- Nutdriver, Socket set
The new motor mount screw holes were not threaded.
I had to tap the screw holes with a 8/32 tap so that the screws would not bind.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Margaret from WINDER, GA
- Parts Used:
- 5304508270
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
From day one the installer did not tighten the screw in the freezer handle. It finally came apart. They didn't leave me the Allen wrench for my fridge.
Simple tightening of the screw with the right tool.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Katie from Hartville, MO
- Parts Used:
- 241761301
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers, Socket set
Moved it from FL to MO left bracket-upper hinge in FL
Used socket set and screw drivers to attach ordered hinge, thankfully we had the screws just not the hinge. Wonderful to be able to find and order on line! Thanks so much!!!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- William from Fort Wayne, IN
- Parts Used:
- 242253002
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Screw drivers, Wrench (Adjustable)
The ice maker and water stopped dispensing
I followed the instructions from your website that I found when ordering the part. It could not have been any easier if I had set in a class room environment. Thanks for all the help and saving me the cost of having someone do a 15 minute repair for 1 hour of labor cost. I would definitely use your site again in the future and I have already put a bug in a couple of my friends ears for if they have issues in the future!! Thanks again!
Was this instruction helpful to you?
Thank you for voting!